8 More Discussions You Might Find Interesting
1. SCO
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Discussion started by: ezlarry
6 Replies
2. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
3. SCO
Hello all,
I'am experiencing weird relyability problems with a SCO 6.0 Openserver server that runs on a Dell Poweredge 1800 equipped with a PERC DC4 raid controller and 4 36 GB 15 K rpm hot swappable scsi harddisks.
It runs a RAID 10 configuration.
It uses the mega hba, Revision 8.03a Release... (1 Reply)
Discussion started by: frederik1
1 Replies
4. UNIX for Dummies Questions & Answers
I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ... (0 Replies)
Discussion started by: skotapal
0 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. Red Hat
I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive.
Using the following kernel parameters, i successfully installed across both hard drives from CD:
ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert... (5 Replies)
Discussion started by: fishsponge
5 Replies
7. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
8. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)