ERROR: ZFS pool <rpool> does not support boot environments.
I have relabeled my disk to SMI label using "format -e" command after creating zpool. But still I am not able to pass through this lucreate step.
Details from my test is below.
Code:
bash 3.2# zpool create rpool c1t5d0
<<Used Format -e command to overwrite SMI label using format -e command>>
bash-3.2# lucreate -c c0t0d0s0 -n newzfsBE -p rpool
Determining types of file systems supported
Validating file system requests
Preparing logical storage devices
Preparing physical storage devices
Configuring physical storage devices
Configuring logical storage devices
Checking GRUB menu...
Analyzing system configuration.
No name for current boot environment.
Current boot environment is named <c0t0d0s0>.
Creating initial configuration for primary boot environment <c0t0d0s0>.
INFORMATION: No BEs are configured on this system.
The device </dev/dsk/c0t0d0s0> is not a root device for any boot environment; cannot get BE ID.
PBE configuration successful: PBE name <c0t0d0s0> PBE Boot Device </dev/dsk/c0t0d0s0>.
ERROR: ZFS pool <rpool> does not support boot environments
WARNING: The boot environment definition file </etc/lutab> was removed because the PBE was not successfully defined and created.
NOTE: I am performing this test on a VM (solaris 10) created on virtualbox.
Kindly suggest what else can be checked or done.
Thanks
Last edited by Scrutinizer; 03-08-2016 at 04:43 PM..
Reason: code tags
I have installed FreeBSD onto a raw image file using QEMU Emulator successfully. I have formatted the image file using the ZFS file system (ZFS POOL).
Using the following commands below I have successfully mounted the image file ready to be opened by zpool
sudo losetup /dev/loop0 .img sudo... (1 Reply)
I have a newly created zpool, and I have set compression on, for the whole pool:
# zfs set compression=on newPool
Now I have zfs send | zfs receive lot of snapshots to my newPool, but the compression is gone. I was hoping that I would be able to send snapshots to the new pool (which is... (0 Replies)
I accidently added a disk in different zpool instead of pool, where I want.
root@prtdrd21:/# zpool status cvfdb2_app_pool
pool: cvfdb2_app_pool
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
cvfdb2_app_pool ONLINE 0 0 0... (1 Reply)
installed Solaris 11 Express on my server machine a while ago. I created a Z2 RAID over five HDDs and created a few ZFS filesystems on it.
Once I (unintentionally) managed to fill the pool completely with data and (to my surprise) the filesystems stopped working - I could not read/delete any... (3 Replies)
Other than export/import, is there a cleaner way to rename a pool without unmounting de FS?
Something like, say "zpool rename a b"?
Thanks. (2 Replies)
I need to migrate an existing raidz pool to a new raidz pool with larger disks. I need the mount points and attributes to migrate as well. What is the best procedure to accomplish this. The current pool is 6x36GB disks 202GB capacity and I am migrating to 5x 72GB disks 340GB capacity. (2 Replies)
I created a pool the other day. I created a 10 gig files just for a test, then deleted it.
I proceeded to create a few files systems. But for some reason the pool shows 10% full, but the files systems are both at 1%? Both files systems share the same pool.
When I ls -al the pool I just... (6 Replies)
# zpool import
pool: emcpool1
id: 5596268873059055768
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: Sun Message ID: ZFS-8000-3C
config:
emcpool1 ... (7 Replies)
Hi all
I plan to install Solaris 10U6 on some SPARC server using ZFS as root pool, whereas I would like to keep the current setup done by VxVM:
- 2 internal disks: c0t0d0 and c0t1d0
- bootable root-volume (mirrored, both disks)
- 1 non-mirrored swap slice
- 1 non-mirrored slices for Live... (1 Reply)