thanks all SAN issue got it seems .after patch update
but still having issue with 10 G network card. if i reset the port from san switch , it will ping the IP and after sometime it's going offline and on Switch side this interface is not learning MAC address.
---------- Post updated 03-20-15 at 01:17 AM ---------- Previous update was 03-19-15 at 03:43 PM ----------
Quote:
Originally Posted by achenle
Did you try known-to-be good FC cables?
Run this under sh/bash:
Code:
for hba in `fcinfo hba-port | grep WWN | awk '{ print $4 }'`; do fcinfo remote-port -ls -p $hba; done
Post the results.
Code:
bash-3.2# for hba in `fcinfo hba-port | grep WWN | awk '{ print $4 }'`; do fcinfo remote-port -ls -p $hba; done
Remote Port WWN: 5006016808603b42
Active FC4 Types: SCSI
SCSI Target: yes
Node WWN: 5006016088603b42
Link Error Statistics:
Link Failure Count: 3
Loss of Sync Count: 256
Loss of Signal Count: 2
Primitive Seq Protocol Error Count: 0
Invalid Tx Word Count: 510
Invalid CRC Count: 1
LUN: 0
Vendor: DGC
Product: LUNZ
OS Device Name: /dev/rdsk/c20t5006016808603B42d0s2
LUN: 1
Vendor: DGC
Product: VRAID
OS Device Name: /dev/rdsk/c1t6006016053C0380015CD88A372B7E411d0s2
LUN: 2
Vendor: DGC
Product: VRAID
OS Device Name: /dev/rdsk/c1t6006016053C03800A680673729CEE411d0s2
Remote Port WWN: 5006016108603b42
Active FC4 Types: SCSI
SCSI Target: yes
Node WWN: 5006016088603b42
Link Error Statistics:
Link Failure Count: 1
Loss of Sync Count: 1
Loss of Signal Count: 1
Primitive Seq Protocol Error Count: 0
Invalid Tx Word Count: 255
Invalid CRC Count: 0
LUN: 0
Vendor: DGC
Product: LUNZ
OS Device Name: /dev/rdsk/c20t5006016108603B42d0s2
LUN: 1
Vendor: DGC
Product: VRAID
OS Device Name: /dev/rdsk/c1t6006016053C0380015CD88A372B7E411d0s2
LUN: 2
Vendor: DGC
Product: VRAID
OS Device Name: /dev/rdsk/c1t6006016053C03800A680673729CEE411d0s2
Remote Port WWN: 5006016408643b42
Active FC4 Types: SCSI
SCSI Target: yes
Node WWN: 5006016088603b42
Link Error Statistics:
Link Failure Count: 0
Loss of Sync Count: 0
Loss of Signal Count: 2
Primitive Seq Protocol Error Count: 0
Invalid Tx Word Count: 255
Invalid CRC Count: 0
LUN: 0
Vendor: DGC
Product: LUNZ
OS Device Name: /dev/rdsk/c12t5006016408643B42d0s2
LUN: 3
Vendor: DGC
Product: VRAID
OS Device Name: /dev/rdsk/c1t6006016053C0380006E0535A33CEE411d0s2
Remote Port WWN: 5006016d08643b42
Active FC4 Types: SCSI
SCSI Target: yes
Node WWN: 5006016088603b42
Link Error Statistics:
Link Failure Count: 0
Loss of Sync Count: 0
Loss of Signal Count: 1
Primitive Seq Protocol Error Count: 0
Invalid Tx Word Count: 255
Invalid CRC Count: 0
LUN: 0
Vendor: DGC
Product: LUNZ
OS Device Name: /dev/rdsk/c12t5006016D08643B42d0s2
LUN: 3
Vendor: DGC
Product: VRAID
OS Device Name: /dev/rdsk/c1t6006016053C0380006E0535A33CEE411d0s2
and moreover fro yesterday onwords i am watching the logs, from another script i did some mount->touch files -> delete files -> unmount is doing. till now no isues for SAN connectivity
But still have issue with network card
---------- Post updated at 01:17 AM ---------- Previous update was at 01:17 AM ----------
Code:
bash-3.2# dladm show-dev
bge0 link: up speed: 1000 Mbps duplex: full
bge1 link: unknown speed: 0 Mbps duplex: unknown
qlge2 link: up speed: 10000 Mbps duplex: full
qlge3 link: unknown speed: 10000 Mbps duplex: half
bash-3.2# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.16.200.52 netmask ffffff00 broadcast 172.16.200.255
ether 0:21:28:d6:41:10
qlge2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 172.16.200.51 netmask ffffff00 broadcast 172.16.200.255
ether 0:c0:dd:29:7f:68
port is showing as UP
what is the steps to diaganose this issue.
Network also same physical layer.
card : Qlogic
Switch : Brocade
---------- Post updated at 05:00 PM ---------- Previous update was at 01:17 AM ----------
HI
any helps please
regards,
Ben
Last edited by Don Cragun; 03-20-2015 at 09:58 PM..
Reason: Fix CODE tags again.
we have opened once case with brocade (switch vendor).and what they find out from server is:
Code:
Type: unknown
State: offline
Current Speed: Not Established
Note:- This implies that the speed not auto negotiable
Type: unknown
Note:- This implies that the Server is not even detecting the Card installed.
Probably, the Drivers/Firmware has to be updated to get this resolved from the Server. There is no issue from the VDX reason being the Connectivity, Link and Protocol status is UP (TenGigabitEthernet 4/0/42 is up, line protocol is up (connected).
and the hba info is showing card as online and is giving the speed as 10 GB
Regards,
Ben
---------- Post updated at 08:46 AM ---------- Previous update was at 06:17 AM ----------
hi
the card is showing as offline always
Code:
HBA Port WWN: 210000c0dd297f69
OS Device Name: /dev/cfg/c16
Manufacturer: QLogic Corp.
Model: 7053422
Firmware Version: 5.08.00
FCode/BIOS Version: BIOS: 3.00; fcode: 3.15; EFI: 3.20;
Serial Number: 463916R+1404161944
Driver Name: qlc
Driver Version: 20140422-5.01
Type: unknown
State: offline
Supported Speeds: 10Gb
Current Speed: not established
Node WWN: 200000c0dd297f69
HBA Port WWN: 210000c0dd297f6b
OS Device Name: /dev/cfg/c17
Manufacturer: QLogic Corp.
Model: 7053422
Firmware Version: 5.08.00
FCode/BIOS Version: BIOS: 3.00; fcode: 3.15; EFI: 3.20;
Serial Number: 463916R+1404161944
Driver Name: qlc
Driver Version: 20140422-5.01
Type: unknown
State: offline
Supported Speeds: 10Gb
Current Speed: not established
Node WWN: 200000c0dd297f6b
but wen we reset the port from switch, it will start ping . that time also card status is offline
Code:
bash-3.2# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
lo0:1: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
zone archibus
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.16.200.52 netmask ffffff00 broadcast 172.16.200.255
ether 0:21:28:d6:41:10
bge0:1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
zone archibus
inet 172.16.200.53 netmask ffffff00 broadcast 172.16.200.255
qlge2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 172.16.200.51 netmask ffff0000 broadcast 172.16.255.255
ether 0:c0:dd:29:7f:68
sppp0: flags=10010008d1<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST,IPv4,FIXEDMTU> mtu 1500 index 4
inet 192.168.254.2 --> 192.168.254.1 netmask ffffff00
How to get LUN WWN (i.e LUN mapped from a storage box say Symmetrix or clariion) in Solaris. fcinfo command does give the Target port wwn but what i'm looking for is the LUN WWN. Any help is appreciated. (2 Replies)
Hi,
GetName()
{
if
then
echo " Please enter the name: "
read Name
tempvar=0
while read line
do
if
then
tempvar=`expr $tempvar + 1`
echo $tempvar
... (10 Replies)
Hi All,
I'm using Solaris server, SunOS 5.10 Generic_144488-08 sun4u sparc SUNW, SPARC-Enterprise.
There is a newly created LUN of 250GB (EMC). I've scanned the system and able to see the new LUN.
For example:
103. emcpower19a <DGC-VRAID-0430 cyl 48638 alt 2 hd 256 sec 16>... (4 Replies)
need to do LUN masking at qlogic HBA level..at RHEL 5.x
I am using qla* module at part of the Unix kernel, it is not OEM drivers that come with the HBA card, so I can't use Sansurfer to do this..
Is there a way to do this at all ??
:wall: (0 Replies)
Hello guys, I'm going crazy over here with a problem with a LUN created on a EMC CX3.
I did sucessfully managed to create the LUN on the Storage (the LUN is named DBLNX25EC_TST), after doing the following process:
echo "1" > /sys/class/fc_host/host<n>/issue_lip
and
echo "- - -" >... (10 Replies)
hi,
what are the steps to detect and configure a new attached lun in Solaris 10.
Is there any difference between cfgadm and luxadm command ?
rgds,
snjksh (5 Replies)
System: Sun M3000 and M4000
OS: Solaris 10 (fully up to date with latest patches)
iSCSI HBA: 2x QLE4060C (QLogic)
In each system are 2 QLE4060C iSCSI adapters.
I manage to set up both HBA's to connect to the LUNs on the SAN
However I don't manage to enable multi-pathing.
Made the... (4 Replies)
I'm piping the results of a tcpdump into a shell script and want certain commands executed (specifically the firing of an SNMP alert) based on a grep for certain contents in the output of tcpdump.
For example, I have
#!/bin/bash
while read str; do
grep 'ttl 64' -q && sudo snmptrap -v 1... (2 Replies)
Is there a limit to the number of LUNS that can be concatenated using Solaris Volume manager with Soft partitions?
I have worked with some AIX admins in the past and there was such a limitation therefore limiting the size the filesystem could grow to.
Is there such a limitation in Solaris 9... (6 Replies)
Hi all,
Can someone advice, why I'm getting a segmentation fault on a Linux system for a program which looks like the below one--:
typedef struct idev{
int p,
char q;
} Idev;
typedef struct abc{
int i;
Idev *idev_ptr;
} ABC;
int main(){
ABC a_var;
char str;
int... (4 Replies)