10 More Discussions You Might Find Interesting
1. Solaris
On an OmniOS server, I removed a single-disk pool I was using for testing.
Now, when I run zpool import it will show it as FAULTED, since that single disk not available anymore.
# zpool import
pool: fido
id: 7452075738474086658
state: FAULTED
status: The pool was last... (11 Replies)
Discussion started by: priyadarshan
11 Replies
2. Solaris
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Discussion started by: rrodgers
2 Replies
3. Solaris
Hello,
I need some help in recovering ZFS pool. Here is scenerio. There are two disks -
c0t0d0 - This is good disk. I cloned it from other server and boot server from this disk.
c0t1d0 - This is original disk of this server, having errors. I am able to mount it on /mnt. So that I can copy... (1 Reply)
Discussion started by: solaris_1977
1 Replies
4. AIX
Dear All,
I created a new partition through "Integrated Virtualization Manager" but there have an error when I added a new disk to the partition. The disk already created without any issue,
Below error is to add the disk to the partition
An error occured while modifying the assignments... (5 Replies)
Discussion started by: lckdanny
5 Replies
5. Solaris
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
Discussion started by: general_lee
2 Replies
6. Solaris
Hi ,
One of my zone went down and when i booted it up i could see the pool in degraded state with some check sum errors . we have brought the pool online after scrubbing. But few files are showing this error
Bad exchange descriptor
Please let me know how to remove these files (2 Replies)
Discussion started by: chidori
2 Replies
7. AIX
Hi
I have one of the disk missing in my NIMVG. My doubt is can I remove this hdisk2 online ? few of the file systems seems to be spread over 7 PV's. that's why i'm worried. Can someone suggest if I can replace this disk online. Also how to check if there is some data present in hdisk2 alone... (2 Replies)
Discussion started by: newtoaixos
2 Replies
8. Red Hat
Hi Everyone,
I have added new Virtual disk to OS. The main point is I need to bring this whole Disk into LVM control, is it necessary to partition the disk using fdisk command and assign partition type as '8e', or can I directly add that disk into LVM, by running pvcreate command with out... (2 Replies)
Discussion started by: bobby320
2 Replies
9. Solaris
I am not seeing anyway to remove a LUN from a Zpool...
Am I missing something? or do i have to destroy the zpool and recreate it? (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
10. Solaris
I had a pool which was exported and due to some issues on my SAN i was never able to import it again. Can anyone tell me how can i destroy the exported pool to free up the LUN. I tried to create a new pool on the same pool but it gives me following error
# zpool create emcpool4 emcpower0c... (0 Replies)
Discussion started by: fugitive
0 Replies
volrootmir(8) System Manager's Manual volrootmir(8)
NAME
volrootmir - Mirror areas necessary for booting to a new disk
SYNOPSIS
/usr/sbin/volrootmir [-a] [nconfig=count] target_disk [swap=target_partition]
OPTIONS
Specifies that all volumes on the system disk be mirrored, not just the root and swap volumes, rootvol and swapvol.
DESCRIPTION
The volrootmir script causes a mirror copy of areas of the root disk involved in booting to be made on the specified target disk.
When used without the -a option, volrootmir adds mirrors of the root and swap volumes and allocates them on the new disk. In addition, all
disk regions required for booting are set up and partitions for the new volume mirrors are created.
When used with the -a option, volrootmir mirrors all in-use partitions on the system disk.
To mirror a swap volume that is on a separate disk from the root volume, the swap attribute must be used to specify a separate target for
the swap mirror.
The target disk(s) must be at least as large as the sum of the sizes of rootvol and swapvol. Also, the physical disk should not have any
disk partition in use.
This script can be called from the voldiskadm menus by choosing the Mirror volumes on a disk operation.
ATTRIBUTES
Specifies the number of log copies and copies of the configuration database, for example, nconfig=2. Specifies that the swap volume,
swapvol, be mirrored on a separate disk, as specified by target_partition.
EXAMPLES
The following command mirrors the rootvol and swapvol volumes onto the target disk, dsk3. This command will fail if swapvol is on a differ-
ent disk from rootvol.
# volrootmir dsk3 The following command mirrors rootvol, swapvol, and any other volumes on the root disk onto the target disk, dsk3.
This command will fail if swapvol is on a different disk from rootvol.
# volrootmir -a dsk3 The following command mirrors rootvol on disk dsk3, swapvol onto partition dsk7d, and any other volumes on the
root disk onto disk dsk3. This command will fail if swapvol is on the same disk as rootvol.
# volrootmir -a dsk3 swap=dsk7d The following command mirrors rootvol onto disk dsk3 and swapvol onto partition dsk7d. This command
will fail if swapvol is on the same disk as rootvol.
# volrootmir dsk3 swap=dsk7d
SEE ALSO
volintro(8), voldiskadm(8)
volrootmir(8)