10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
2. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
3. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
7. IP Networking
Hello,
I'm working on LACP architecture. I would like to know if it's possible to aggregate two links on two separate switches.
Here an example I want : Aggregation of link1 and link2 to obtain a logical 2 gbit/s link. Also have redundancy, if one of them is down, the traffic goes through the... (1 Reply)
Discussion started by: jbemonet
1 Replies
8. IP Networking
Hello, I am trying to get clarity on a few things and am looking for some info.
In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth.
But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Discussion started by: jaredo
1 Replies
9. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
10. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies