Haed code nxge0 nic interface with full duplex & 1000mbps
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
Solaris - 10 Sparc
Please suggest to make bnx2 as full duplex with speed 1000 Mbps which is currently at speed 100 Mbps
>dladm show-dev
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 link: unknown speed: 0 Mbps duplex: half
e1000g2 ... (2 Replies)
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Hi,
the following code comes from Unix Linux dialog utility project.
Unfortunately, this project is no more actively maintained.
Unix Linux dialog utility is made of widget boxes.
One of them is mixedgauge.c
In the following example I would like to get rid of flickering
when run in... (0 Replies)
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
Dear Members,
I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
TXP(4) BSD Kernel Interfaces Manual TXP(4)NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device txp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_txp_load="YES"
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu-
tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
HARDWARE
The txp driver supports the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3cR990B-TXM
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
o 3Com 3cR990B-SRV
SEE ALSO altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8)HISTORY
The txp driver first appeared in OpenBSD 2.9.
BSD March 12, 2009 BSD
