Before plumb the network interface.....

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

7. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ...

8. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks!

9. Gentoo

Turning on/off the network interface

Hi all, I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help? Thanks, Neked

10. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT OPENSOLARIS

net_lifgetnext

net_lifgetnext(9F)					   Kernel Functions for Drivers 					net_lifgetnext(9F)

NAME

       net_lifgetnext - search through a list of logical network interfaces

SYNOPSIS

       #include <sys/neti.h>

       net_if_t net_lifgetnext(const net_data_t net, const phy_if_t ifp,
	    net_if_t lif);

INTERFACE LEVEL

       Solaris DDI specific (Solaris DDI).

PARAMETERS

       net    value returned from a successful call to net_protocol_lookup(9F).

       ifp    value returned from a successful call to net_phylookup(9F) or net_phygetnext(9F).

       lif    value returned from a successful call to this function.

DESCRIPTION

       The  net_lifgetnext()  function	is used to search through all of the logical interfaces that are associated with a physical network inter-
       face. To start searching through this list, a value of 0 should be passed through as the value of lif. When 0 is returned by this function,
       the last of the interfaces owned by this protocol has been reached.

       When  called  successfully, the value returned represents a logical interface that exists, at the time of the call, within the scope of the
       network interface and its assigned network protocol. This value is only guaranteed to be unique for a name within the scope of the  network
       interface and its assigned protocol.

EXAMPLES

	    net_data_t net;
	     phy_if_t ifp;
	     net_if_t lif;
	     char buffer[32];
	     net_ifaddr_t atype[1];
	     struct sockaddr_in sin[1];

	     net = net_protocol_lookup("inet");

	     if (net != NULL) {
		  atype[0] = NA_ADDRESS;
		  ifp = net_phylookup(net, "hme0");
		  for (lif = net_lifgetnext(net, 0); lif != 0;
			lif = net_lifgetnext(net, lif)) {
			/* Do something with lif */
			if (net_getlifaddr(net, ifp, lif, 1, atype, sin) == 0)
			      printf("hme0:%d %x0, lif,
				  ntohl(sin[0].sin_addr.s_addr));
		   }
	       }

RETURN VALUES

       The  net_lifgetnext()  function	returns  a value of -1 if it is not supported by the network protocol and a value of 0 if an attempt to go
       beyond the last network interface is made. Otherwise, it returns a value representing a network interface.

CONTEXT

       The net_lifgetnext() function may be called from user,  kernel, or interrupt context.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcsu			   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Committed 		   |
       +-----------------------------+-----------------------------+

SEE ALSO

       net_phygetnext(9F), net_phylookup(9F)

SunOS 5.11							    1 May 2008							net_lifgetnext(9F)

Solaris