10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
2. Shell Programming and Scripting
I am trying to read the Sparc HW counter using the following command:
cpustat -c Instr_cnt .1This command will be running forever (for some time until interrupted by user). Sample output is:
time cpu event pic1
1.011 0 tick 6450
1.011 1 tick ... (10 Replies)
Discussion started by: Zam_1234
10 Replies
3. Shell Programming and Scripting
Hi All,
i am trying to retrive below information from any hp-ux machine (physical & virtual both):
1.Processor Total Count:
2.Processor Core Count:
3.Processor type:
4.number of physical processors:
5 number of virtual processors:
i am trying to use command 'print_manifest' as... (0 Replies)
Discussion started by: omkar.jadhav
0 Replies
4. Solaris
Hi all,
I have application running on sun server T5440 4x8x1.4 GHz, 64 GB RAM, application running very slow though load average too low. when I install my application on another server SUN M3000 (One CPU 1x8x2.5GHz, 8GB RAM), application run smoothly.
Here is my server T5440 info:
... (6 Replies)
Discussion started by: insatiable1610
6 Replies
5. Solaris
Failed to recover lost root password for Solaris SunSparc
(On Sun Ultra10 - SPARC CPU Hardware, not x86 Intel CPU nor x64 AMD CPU)
This Sun Ultra10 workstation comes with an old 6-in wafer probing station purchased from a Surplus equipment vendor.
Computer: Sun Ultra 5/10 UPA/PCI... (21 Replies)
Discussion started by: fromtexas0
21 Replies
6. Infrastructure Monitoring
Can someone please tell me how to calculate the CPU usage from what one gets back from snmpwalk?
I have searched and dug through the internet and apparently, no one has the answer to this?
i can use snmpwalk to pull out relevant information about cpu. but i have no clue what values are to be... (1 Reply)
Discussion started by: SkySmart
1 Replies
7. Infrastructure Monitoring
Hi,
I have sucessfully set up snmp daemon on my AIX box (v 6.1.2.0).
I can query snmp from localhost (using command: snmpinfo -v -m dump -c public mib-2) and it works perfectly.
But I don't get any reply when query my AIX box from remote machine (AIX, Linux,...)
I have tried to set up SNMP v1... (0 Replies)
Discussion started by: pavel.kovar
0 Replies
8. Solaris
Hi ,
could you please clarify me the difference between sun sparc 32-bit and sun sparc 64-bit?
means on which processors these are supporting (pentium processors, sun sparc processors)
Regards,
Rajesh (1 Reply)
Discussion started by: pmrajesh21
1 Replies
9. UNIX for Advanced & Expert Users
Hi
I would like to monitor CPU usage ( %) , memory utilization and such on an AIX 5.3 with snmp.
How would I do that ? :confused:
If I do "snmpwalk -c public -v1 hosttomonitor" I get nothing about the CPU.
I've done this on Linux ( not much trouble doing it on linux ) but I'm having a hard... (2 Replies)
Discussion started by: art
2 Replies
10. UNIX for Dummies Questions & Answers
Hi, I'm new to this forum AND to UNIX and here are my questions:
I have a Sun V480 server sitting here, and I would like to use it. Mainly just for education. Now, I would like to know if I can buy a videocard and a soundcard and install them on this machine? I have looked at som videocards, but... (1 Reply)
Discussion started by: hyperion
1 Replies
SNMP - cpu core information for Sun SPARC machine