10 More Discussions You Might Find Interesting
1. Hardware
I have a problem,
I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited).
The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable"
I have... (5 Replies)
Discussion started by: hhaswan
5 Replies
2. Hardware
Hello all.
I have a requirement to install a aftermarket video card in the server, can you advise what fits? or if there is a sun riser part which convers the PCIx slot to PCIe
The unit is a standard x4100 with PCIx slots, not an M2 with the PCIe slots.
thanks (4 Replies)
Discussion started by: petebarchetta
4 Replies
3. Hardware
hi
please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition.
thanks (2 Replies)
Discussion started by: bahjatm
2 Replies
4. Solaris
Howto boot from Cd-rom in Server Sunfire v250?
The system can't boot because the filesystem is corrupt.
The system say:
run manually fsck -F ufs /dev/rdsk/c0t0d0s5
But, I don't now how to make this.
I tried use stop + a, but nothing hapend.
Someone can I help? (13 Replies)
Discussion started by: vigux
13 Replies
5. Solaris
Hi Gurus
I would like to know whether break command always work well means take the system to ok> prompt. Its depend upon sever model also. As I am facing problem when ever my system ( Sunfire V890 ) having Solaris 10 OS & oracle RAC on it goes to hang state then I run the break command from... (6 Replies)
Discussion started by: girish.batra
6 Replies
6. Solaris
I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies
7. Solaris
Hi everyone,
I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1.
When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies
8. Solaris
Hai All
I rquire a small help for Galaxy x4100 server, when we are trying to sepup
ILOM through CLI it gives following error on commitpending=true steps.
set pendingipaddress=172.21.142.158
Set 'pendingipaddress' to '172.21.142.158'
-> set pendingipgateway=172.21.142.5
Set... (1 Reply)
Discussion started by: sure.solaris
1 Replies
9. Solaris
Hi there
I am running solaris 10 on an SunFire x4100 ...(x86 box) Could anybody tell me if there is a way I can check the firmware revision without taking the box down to do it ...eeprom doesnt give me the info I require
Cheers (0 Replies)
Discussion started by: hcclnoodles
0 Replies
10. Solaris
Hi there
the Sunfire X4100 has a great tool that you can get to from BIOS called the configuration utility which allows you to set up Disk mirroring (RAID 1) before the OS sees it, which is great and it works a treat, however, we have a large datacentre across multiuple sites and I need to find... (1 Reply)
Discussion started by: hcclnoodles
1 Replies