Supporting NIC speed

10 More Discussions You Might Find Interesting

1. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out?

2. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

3. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

4. UNIX for Advanced & Expert Users

Determine the ethernet (NIC) card speed.

Hi, Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux. I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS....

5. Solaris

change NIC speed

how can we change the nic card speed please explain through commands & steps ???? and i want to change NIC speed 100 --1000Mbps and what is full & half duplex gives thanks in advance

6. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj

7. Filesystems, Disks and Memory

data from blktrace: read speed V.S. write speed

I analysed disk performance with blktrace and get some data: read: 8,3 4 2141 2.882115217 3342 Q R 195732187 + 32 8,3 4 2142 2.882116411 3342 G R 195732187 + 32 8,3 4 2144 2.882117647 3342 I R 195732187 + 32 8,3 4 2145 ...

8. IP Networking

NIC speed 100M/full duplex problem

I have a TOSHIBA AS7000 B150 Sun Box I wanted to run it with 100M/full duplex I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot. set eri:eri_adv_100fdx_cap=1 set eri:eri_adv_100hdx_cap=0 set eri:eri_adv_autoneg_cap=0 But when I...

9. Solaris

Sun box's NIC speed setting

Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps? Thanks!

10. Solaris

How to check Virtual NIC card speed on solaris

Hi, We have a 4 port Sun gigaswift NIC card on our sun fire server. If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings. Details ----------- root:/> ifconfig -a lo0:...

LEARN ABOUT DEBIAN

install-solaris

install-solaris(1M)													       install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris	invokes  the  Solaris  Install	program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

	   Minimum physical memory for all installation types

       128 MB

	   Minimum physical memory required for windowing system

       384 MB

	   Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

	   Minimum physical memory for all installation types

       256 MB

	   Minimum physical memory required for windowing system

       512 MB

	   Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris	exists	only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcdrom  (Solaris instal-  |
       |			     |lation media)		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

								    23 Sep 2005 					       install-solaris(1M)

Solaris