6 More Discussions You Might Find Interesting
1. Solaris
Hi,
Can someone tell me how to re-activate the root login of T1000 sun solaris server.
Thx (1 Reply)
Discussion started by: abdull
1 Replies
2. Solaris
Hi,
we are having one sun v240 server, now this server is performing very slow,
checked using top, iostat and vmstat commands, output is looking normal, but the performance is very slow and generating more traffic in network,
how can we resolve this.
Regards
RJS (5 Replies)
Discussion started by: rajasekg
5 Replies
3. Filesystems, Disks and Memory
Hello,
i have a a1000 connected to an e6500. There's a raid 10 (12 disks) on the a1000.
If i do a
dd if=/dev/zero of=/mnt/1 bs=1024k count=1000
and then look at iostat it tells me there's a kw/s of 25000.
But if i do a
dd of=/dev/zero if=/mnt/1 bs=1024k count=1000
then i see only a... (1 Reply)
Discussion started by: mbrenner
1 Replies
4. Solaris
Hello All.
I have Sun T1000 server with Solaris 10.
On T1000 installed EMC smarts, application for monitoring network devices via SNMP + SNMP.
So, Smarts has own DB (contains object - devices and relationships), file takes 30 mb, now, all queries to DB works very slow, so Smarts works too slow,... (5 Replies)
Discussion started by: hemulll
5 Replies
5. Solaris
Guys where can i find values to add in /etc/system to make sun solaris 10 working better ? im sure there is alot of values but i dont know from where i can find them if you know any please send direct and if you know another sites send links to it, thanks so much. (5 Replies)
Discussion started by: XP_2600
5 Replies
6. AIX
I am posting this as an FYI. I burned a lot of time on digging for this solution. The problem was performance between newer AIX p series boxes and a sun 4500 with a fiber nic. I tried many misc. solutions but this turned out to fix the issue. My bandwidth benchmark went from around 20MB/sec to... (1 Reply)
Discussion started by: chuckw
1 Replies
MPT(4) BSD Kernel Interfaces Manual MPT(4)
NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device mpt
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mpt_load="YES"
DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers.
HARDWARE
The following controllers are supported by the mpt driver:
o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI)
o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA)
o LSI Logic FC909 (1Gb/s Fibre Channel)
o LSI Logic FC909A (Dual 1Gb/s Fibre Channel)
o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel)
o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel)
o LSI Logic FC949X (Dual 4Gb/s Fibre Channel)
o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express)
The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including:
o Dell PowerEdge 1750 thru 2850
o IBM eServer xSeries 335
These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports.
The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both
SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at
best.
The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the
FC949ES card.
This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the
LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required.
SEE ALSO
cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8)
LSI Logic Website, http://www.lsilogic.com/.
HISTORY
The mpt driver first appeared in FreeBSD 4.6.
AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>.
Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements.
BUGS
BSD
May 13, 2010 BSD