10 More Discussions You Might Find Interesting
1. Solaris
Hello Folks, can anyone please help me with this ?! :wall:
I'm using Solaris 10 with Sun V880 which has two Networks Interfaces, a Fiber (ge0) and a cooper (eri0).
The eri0 is working great but when I try to plumb the ge0 interface ...
# ifconfig ge0 plumb
ifconfig: cannot open link... (18 Replies)
Discussion started by: pxb368@motorola
18 Replies
2. Solaris
Ultra E150 Solaris 2.5.1 Oracle server. was working fine, then started losing network connection. I can see in messages file that it was complaining about another device using its ip address. Though not any longer, though I wonder if that was a red herring. My IT guys have now re-reserved its ip... (29 Replies)
Discussion started by: AlSmith1964
29 Replies
3. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
4. Solaris
Hi All,
I logged into a sun microsystems server box, using both a vnc session and a ssh session. I am able to use "ifconfig -a" in a ssh session, but the same on a vnc session says that its a invalid command. how is this possible, when i am logging into the same box through two different... (4 Replies)
Discussion started by: pardhuhere
4 Replies
5. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
6. UNIX for Dummies Questions & Answers
I have sun solaris 9 installed but I have the interface configured to hme1 instead of hme0, our default value.
Is there a way where i can rename the existing/working hme1 to hme0...?
I want to showup the hmeo up if i say ifconfig -a..
rite now i see the hme1 up..
please advice if possible... (4 Replies)
Discussion started by: tintedwindow
4 Replies
7. Solaris
I know that I could use the
#ifconfig hme0 plumb
to activate the network interface.
However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up?
I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies
8. Solaris
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies
9. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
10. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies