10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Recently, I setup a dual boot on this PC. I can currently jump from Ubuntu 12.04 and 16.04. What I would like to be able to do is access the home directory of my 16.04 OS from within the 12.04, is that possible? I can mount the partition of the hard drive where 16.04 lives from within 12.04 but it... (4 Replies)
Discussion started by: Circuits
4 Replies
2. Red Hat
hi all,
As going thru LVM concepts in rhel 6, got hit with a question about "how to use the raw partition of an harddisk which extended volume is taken a bit"
please find the attached diagram...
is it possible to use this raw space with previously created extended partition without data... (13 Replies)
Discussion started by: redhatlbug
13 Replies
3. Solaris
Dear all,
We have a Solaris Server at other location. Can we access the Server from remote ....Any software is needed for this ....pl help.
Rgds
Rj (7 Replies)
Discussion started by: jegaraman
7 Replies
4. Solaris
This is the error message that I am getting on a Solaris 10 sparc server
scsi: no major number
cannot load drivers for /pci@400.....
Can't load the root filesystem
Type 'go' to resume
{0} ok
Is there a way for me to correct this issue. It looks like I am missing a scsi driver to boot up... (5 Replies)
Discussion started by: trinityforce
5 Replies
5. Shell Programming and Scripting
Folks,
I'm a perl moron, so please speak very slowly. : )
I'm modifying a build script that starts up an apache server. Now there is a .config file that hardcodes an old webserver path like this c:\oldWebserver. Now I don't want that hardcoded value, rather wish to use an... (3 Replies)
Discussion started by: MarkoRocko
3 Replies
6. Hardware
Hi all,
I need to configure the zte zxv10 w300 modem, but can't access to it control panel. Seems to hide or mask it IP address. Someone knows howto access or setup a new configuration ? a hard reset maybe ? then looking in a default IP address ? how is this ?
Thanks in advance
VicK (0 Replies)
Discussion started by: VicK
0 Replies
7. Red Hat
Hello, every one,
I tried to install redhat linux enterprise server version 4 (ES4) on the my system with the
following configuration
Pentium core 2 duo 2.66 E 6750
Intel DG33FB motherboard
160Gb Segate hard disk (SATA)
1024 mb (1GB) DDR2 TRAN RAM
Lg DVD/Cd WR
BUT AM GETTING... (0 Replies)
Discussion started by: moinkhan31
0 Replies
8. Solaris
Hello All,
I am quite new to Solaris.
Can someone tell me what's the equivalent of HP-UX ps -efx on Solaris? It basically displays the whole command, instead of te first 80 characters of the command.
I need that to differentiate among multiple Weblogic processes where all the specifics... (1 Reply)
Discussion started by: usfrog
1 Replies
9. IP Networking
We can access our solaris 8 from our LAN . However when we try to
access the same over our WAN , it is not able to ping the server .
/etc/hosts has entries for our DNS server. Another thing all WAN clients
are Windows 2000 workstations .
Here is the output netstat -nr
Routing Table: IPv4... (7 Replies)
Discussion started by: Hitesh Shah
7 Replies
10. Solaris
Hi,
i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card .
Thank You,
Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies
PCITWEAK(1) General Commands Manual PCITWEAK(1)
NAME
pcitweak - read/write PCI config space
SYNOPSIS
pcitweak -l
pcitweak -r PCI-ID [-b|-h] offset
pcitweak -w PCI-ID [-b|-h] offset value
DESCRIPTION
Pcitweak is a utility that can be used to examine or change registers in the PCI configuration space. On most platforms pcitweak can only
be run by the root user.
OPTIONS
-l Probe the PCI buses and print a line for each detected device. Each line contains the bus location (bus:device:function), chip
vendor/device, card (subsystem) vendor/card, revision, class and header type. All values printed are in hexadecimal.
-r PCI-ID
Read the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in the form
bus:device:function, with each value in hexadecimal. By default, a 32-bit register is read.
-w PCI-ID
Write value to the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in
the form bus:device:function, with each value in hexadecimal. By default, a 32-bit register is written.
-b Read or write an 8-bit value (byte).
-h Read or write a 16-bit value (halfword).
SEE ALSO
scanpci(1)
AUTHORS
David Dawes (dawes@xfree86.org).
XFree86 Version 4.7.0 PCITWEAK(1)