I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc
and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it to a bridge. So now I'm trying to create a bridge with
(Don't know if the command is correct, remember, I'm an absolute begineer)
The problem is that it returns:
from the official doc:
Quote:
bridge-name is an arbitrary string that must be a legal SMF service instance name. This name is a FMRI component that has no escape sequences, which means that whitespace, ASCII control characters, and the following characters cannot be present:
; / ? : @ & = + $ , % < > # "
Should I report this as a bug? And, if so, where? Or I'm doing something wrong?
---------- Post updated at 03:31 PM ---------- Previous update was at 01:18 PM ----------
again, I can't get it working.
I've installed and booted the zone, and then I've tried to connect to it:
Quote:
root@myhostname:/zones# zlogin -C external
[Connected to zone 'external' console]
I can't do anything. I'm seriusly thinking to install the old release of solaris, but first... what am I supposed to do in order to (try to) solve this problem?
ID NAME STATUS PATH BRAND IP
0 global running / solaris shared
2 external running /zones/external solaris excl
Quote:
create -b
set zonepath=/zones/external
set brand=solaris
set autoboot=true
set ip-type=exclusive
add net
set configure-allowed-address=true
set physical=vnic0
end
add anet
set linkname=net0
set lower-link=auto
set configure-allowed-address=true
set link-protection=mac-nospoof
set mac-address=random
set auto-mac-address=2:8:20:9b:eb:9c
end
Hi all,
I have never wondered where is the mapping of the link names to physical device path display under
dladm show-phys until today.
fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is... (1 Reply)
Hello unix community,
Could anyone tell me what is the macosx command for:
1) ip hostroute to bridge:
ip route add 188.40.1.40/32 dev br0
(linux command)
/32 ist for netmask? Because I use /29.
2) and IP-Forwarding:
net.ipv4.ip_forward = 1
(linux command)
I hope anyone could... (1 Reply)
hello networking folks,
i have 3 virtual machines that need to talk to each other
How can i create a bridge to loopback ?
-net tap,vlan=0,ifname=tap1
where tap1 is connected to lo:1 , tap2 is connected to lo:2 etc
thx (0 Replies)
I have a laptop running Ubuntu Netbook Remix.
What I want to do is use it to connect to my routers wifi, and then plug my desktop into the laptops ethernet port and be hooked to my routers network without any NAT or ICS.
Desktop>>>>>>Laptop/Wired>>Laptop/Wireless>>>>>Router
I want it to look... (6 Replies)
Can anyone please explain what does these means ?
# dladm show-dev
nxge0 link: up speed: 1000 Mbps duplex: full
nxge1 link: up speed: 1000 Mbps duplex: full
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 ... (6 Replies)
Greetings
how can i remove an interface from dladm?
i want to remove ce3 and ce4 which are not even plumbed but still shown in dladm output :(
dladm show-dev
ce0 link: unknown speed: 1000 Mbps duplex: full
ce1 link: unknown speed: 1000 Mbps duplex:... (3 Replies)
Hello all, recently we've created a Bridge on a machine that was being used as an snmp, and we haven't assigned an IP for the bridge interface, instead we've used one extra NIC to make all the administrations, but SNMP is simply not working, any one have a clue on how to do this?
Thanks. (0 Replies)
Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this:
dladm create aggr -d ce0 -d ce1 key
Do I need to... (1 Reply)
Hello.
I expirince some problems with bridging, i'm pretty new to that technology
I've 2 nic's 1 - wireless rt2500 ra0 canyon cn511 card
2 - e100 intel,
ifconfig ra0 up && iwconfig ra0 essid xxx channel x mode managed bring me wireless connection up
then i do following: brctl addbr br0... (1 Reply)