nxge: [ID 339653 kern.notice] NOTICE: nxge0: xcvr addr:0x0d - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge1: xcvr addr:0x0c - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge2: xcvr addr:0x0b - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge3: xcvr addr:0x0a - link is down
Why these messages are coming repeatedly. These interfaces are not using.
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Im getting stumped on one of my unix problems. Im a college student taking unix and for one of my assignments I am to write a few programs. I done the programs but on one of them I have to modify it by using sed instead of a while do loop. here's the while loop
while
do
... (2 Replies)
Pls can u help me diagnosed this Notice l receive during booting of my openserver 5.0.4 unix from the kernel.
NOTICE:cha:SCSI bus has been reset ha=0
Attached SCSI peripherals will retunr to power up
state (ChaN04)
NOTICE:cha:SCSI command timed out ha=0... (2 Replies)
Discussion started by: kayode
2 Replies
7. Post Here to Contact Site Administrators and Moderators
MTEST(8) BSD System Manager's Manual MTEST(8)NAME
mtest -- test multicast socket operations
SYNOPSIS
mtest
DESCRIPTION
The mtest utility is a small program for testing multicast socket operations.
It accepts the following commands, interactively, or as part of a scripted input file (useful for automated testing):
a ifname mac-addr Join the link-layer group address mac-addr on interface ifname. The group address should be in IEEE 802 MAC
format, delimited by colon (':') characters.
d ifname mac-addr Leave the link-layer group address mac-addr on interface ifname.
m ifname 1/0 Set or reset ALLMULTI mode on interface ifname. This option is deprecated and is now a no-op.
p ifname 1/0 Set or reset promiscuous mode on interface ifname.
j mcast-addr ifname [source-addr]
Join the multicast address mcast-addr on the interface with name ifname.
If an optional source source-addr is specified, a source-specific join will be performed; if mtest is already
joined to the multicast address, the source will be added to its filter list.
l mcast-addr ifname [source-addr]
Leave the multicast address mcast-addr on the interface with address ifname. If a source source-addr is
specified, only that source will be left.
i mcast-addr ifname n source-addr ...
Set the socket with membership of mcast-addr on interface ifname to include filter mode, and add n sources
beginning with source-addr to the inclusion filter list.
e mcast-addr ifname n source-addr ...
Set the socket with membership of mcast-addr on interface ifname to exclude filter mode, and add n sources
beginning with source-addr to the exclusion filter list.
t mcast-addr ifname source-addr
Set the socket with membership of mcast-addr on interface ifname to block traffic from source source-addr.
b mcast-addr ifname source-addr
Set the socket with membership of mcast-addr on interface ifname to allow traffic from source source-addr.
g mcast-addr ifname n Print n source filter entries for mcast-addr on interface ifname.
f filename Read commands from the file filename.
s n Sleep for n seconds.
? List legal commands.
q Quit the program.
IMPLEMENTATION NOTES
For each command implemented by mtest, the address family of each argument must be identical; it is not possible to mix IPv4 multicast mem-
berships with IPv6, for example.
To support IPv6, all commands have now changed to accept an interface name rather than an interface address. For IPv4, the program will per-
form a lookup of the primary IP address based on the interface name. This may fail if no primary IP address is assigned.
SEE ALSO
D. Thaler, B. Fenner, and B. Quinn, Socket Interface Extensions for Multicast Filters, RFC 3678.
AUTHORS
Bruce Simpson
Steve Deering
Wilbert De Graaf
BSD April 29, 2009 BSD