7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
3. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. UNIX for Dummies Questions & Answers
Im getting stumped on one of my unix problems. Im a college student taking unix and for one of my assignments I am to write a few programs. I done the programs but on one of them I have to modify it by using sed instead of a while do loop. here's the while loop
while
do
... (2 Replies)
Discussion started by: gummiworm
2 Replies
6. UNIX for Advanced & Expert Users
Pls can u help me diagnosed this Notice l receive during booting of my openserver 5.0.4 unix from the kernel.
NOTICE:cha:SCSI bus has been reset ha=0
Attached SCSI peripherals will retunr to power up
state (ChaN04)
NOTICE:cha:SCSI command timed out ha=0... (2 Replies)
Discussion started by: kayode
2 Replies
7. Post Here to Contact Site Administrators and Moderators
Hi. I moved this site to a T3 facility and wanted to know if any of the long time users noticed a performance improvement? Thanks, Neo. (5 Replies)
Discussion started by: Neo
5 Replies
GSL(1) General Commands Manual GSL(1)
NAME
gsl-config - script to get version number and compiler flags of the installed GSL library
SYNOPSIS
gsl-config [--prefix] [--version] [--libs] [--libs-without-cblas] [--cflags]
DESCRIPTION
gsl-config is a tool that is used to configure to determine the compiler and linker flags that should be used to compile and link programs
that use GSL. It is also used internally to the .m4 macros for GNU autoconf that are included with GSL.
OPTIONS
gsl-config accepts the following options:
--version
Print the currently installed version of GSL on the standard output.
--libs Print the linker flags that are necessary to link a GSL program, with cblas
--libs-without-cblas
Print the linker flags that are necessary to link a GSL program, without cblas
--cflags
Print the compiler flags that are necessary to compile a GSL program.
--prefix
Show the GSL installation prefix.
SEE ALSO
gtk-config(1), gnome-config(1)
COPYRIGHT
Copyright (C) 2001 Christopher R. Gabriel
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, pro-
vided that the above copyright notice appear in all copies and that both that copyright notice and this permission notice appear in sup-
porting documentation.
22 May 2001 GSL(1)