nxge: [ID 339653 kern.notice] NOTICE: nxge0: xcvr addr:0x0d - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge1: xcvr addr:0x0c - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge2: xcvr addr:0x0b - link is down
nxge: [ID 339653 kern.notice] NOTICE: nxge3: xcvr addr:0x0a - link is down
Why these messages are coming repeatedly. These interfaces are not using.
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Im getting stumped on one of my unix problems. Im a college student taking unix and for one of my assignments I am to write a few programs. I done the programs but on one of them I have to modify it by using sed instead of a while do loop. here's the while loop
while
do
... (2 Replies)
Pls can u help me diagnosed this Notice l receive during booting of my openserver 5.0.4 unix from the kernel.
NOTICE:cha:SCSI bus has been reset ha=0
Attached SCSI peripherals will retunr to power up
state (ChaN04)
NOTICE:cha:SCSI command timed out ha=0... (2 Replies)
Discussion started by: kayode
2 Replies
7. Post Here to Contact Site Administrators and Moderators
NXGE(4) BSD Kernel Interfaces Manual NXGE(4)NAME
nxge -- Neterion Xframe 10GbE Server/Storage adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device nxge
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_nxge_load="YES"
DESCRIPTION
The nxge driver provides support for Neterion Xframe-I and Xframe-II adapters. The driver supports TCP Segmentation Offload (TSO/LSO), Large
Receive Offload (LRO), Jumbo Frames (5 buffer mode), Header Separation (Rx 2 buffer mode), VLAN, and Promiscuous mode.
For general information and support, please visit the Neterion support page http://www.neterion.com/support/support.html.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to transmit and receive Jumbo Frames. Xframe adapters support Jumbo Frames up to 9600 bytes.
For Jumbo Frames, the driver will try to allocate physically contiguous buffers. Failures to do so may degrade the performance. To resolve
such problems, please visit http://www.neterion.com where additional information and a kernel patch can be found.
For more information on configuring this device, see ifconfig(8).
HARDWARE
The nxge driver supports Neterion Xframe 10 Gigabit Ethernet adapters listed in http://www.neterion.com/how/pricing.html.
SUPPORT
For troubleshooting tips and FAQs, please visit http://trac.neterion.com/cgi-bin/trac.cgi/wiki/TitleIndex?anonymous.
For any issues please send an email to <support@neterion.com>.
SEE ALSO arp(4), netintro(4), ifconfig(8)HISTORY
The nxge device driver first appeared in FreeBSD 7.0.
AUTHORS
The nxge driver was written by Neterion <support@neterion.com>.
BSD October 16, 2007 BSD