10 More Discussions You Might Find Interesting
1. Solaris
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
2. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
3. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
4. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
5. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
6. Solaris
Hi Gurus
I need to know few things related to HBA port & fcinfo command
I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above... (6 Replies)
Discussion started by: girish.batra
6 Replies
7. Solaris
I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install?
Thanks in advance.... (23 Replies)
Discussion started by: Y4Net
23 Replies
8. IP Networking
I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB?
Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies
9. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
10. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
quaggaadm(1M) quaggaadm(1M)
NAME
quaggaadm - quagga routing daemon administration tool
SYNOPSIS
quaggaadm [-e] zebra|ripd|ripngd|ospfd|ospf6d|bgpd|isisd
DESCRIPTION
The quaggaadm command is provided as a simple wrapper to facilitate connection to the quagga daemons respective vty terminal telnet inter-
faces, in a similar manner to zebraadm, which was provided as part of SUNWzebra. quaggaadm simply telnets the appropriate vty port for the
specified daemon on localhost, and from there the user can update configuration for that daemon. Note that if the vty is disabled for the
given daemon, quaggaadm will prompt the user to request enable. Note that to complete this operation, the user will require
solaris.smf.manage.routing and solaris.smf.modify.routing authorizations.
OPTIONS
The following command-line options are supported:
-e
Automatically enable the vty for the specified daemon.
EXIT STATUS
The following exit values are returned:
0
Successful completion.
!=0
An error occurred while obtaining or modifying the system configuration.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWquaggar |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
quagga(1M), attributes(5), routeadm(1M)
02 Oct 2008 quaggaadm(1M)