The white paper you quote predates exclusive-ip zones so isn't very helpful. As an update to what I previously wrote, if you want to stay with shared-IP zones and are using a recent enough Solaris release, you might also use the defrouter zone configuration parameter to overcome the previously mentioned restriction. see Using zonecfg defrouter with shared-IP zones - What the krowteN? for details.
We use the "default router" parameter in all our zones. But the packets still do not leave the global zone because of the "shared" ip-type parameter. I have not tried the "exclusive" ip zone implementation yet. Here is one of our zone configs:
Code:
root@globalzone# zonecfg -z localzone export
create -b
set zonepath=/ZONES/localzone
set autoboot=false
set ip-type=shared
add net
set address=10.10.19.132/27
set physical=nxge0
set defrouter=10.10.19.158
end
Jlliagre - I have read this blog which discusses inter-zone traffic isolation and plan to test this before implementing an exclusive IP zones.
ALSO, all the zones are built on Solaris 10 9/10 (update 9) release.
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Hi All
Kindly let me know how can I move Solaris 10 OS running update 10 on physical machine to another machine solaris zone running Solaris 10 update 11 (2 Replies)
Dear,
I hope you all will be ok.
I have an issue with Solaris box running on x86 Blade.
I am unable to ping a node neither traceroute. I am able to do traceroute from oce0:6 port which have IP and subnet of same type which oce0:1 has.
details are as follows:
Problem:
root@rinams02:/#... (3 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hi all,
I'm having some trouble identifying what route is being used to talk to a target host. I can figure it out by looking at the routing tables but I want to automate this and don't much feel like scripting the network mask logic when I'd think there'd be a way to have the OS do it for me.... (5 Replies)
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
