10 More Discussions You Might Find Interesting
1. Solaris
I've followed a few guides and have what appears to be a working jumpstart server. I can PXE boot a bare system, it gets an IP and launches the installer. However, it takes me to the screen:
SunOS Release 5.10 Version generic-147148-26 64 bit
Copyright (c) 1983, 2013, Oracle and/or its... (1 Reply)
Discussion started by: jnojr
1 Replies
2. Solaris
I 'm tryin to install a solaris server After all the system initialization & extraction of flash archive installation aborts with following error ..
Does anyone know what could be the issue for the same ?
Any help would be appreciated
Extracted 2205.05 MB ( 99% of 2205.54 MB... (6 Replies)
Discussion started by: fugitive
6 Replies
3. Solaris
I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created:
install_type
initial_install
system_type server
cluster SUNWCXall... (4 Replies)
Discussion started by: msarro
4 Replies
4. Solaris
I have a jumpstart client that is not requesting the tftp boot file. The rarp function is working, hostname and ip are set ok, but it hangs after that.
tcpdump output:
jumpstart-server:/var/lib/tftpboot# tcpdump -i eth1
tcpdump: verbose output suppressed, use -v or -vv for full protocol... (6 Replies)
Discussion started by: skitch
6 Replies
5. Solaris
I have created profile file for zfs root (flash) on a wanboot server when i try to validate the rules file with check i get following error .. i 'm not sure why i 'm getting this error .. can any one help me on this ?
# ./check
Validating rules...
Validating profile profile...
Error in... (0 Replies)
Discussion started by: fugitive
0 Replies
6. Solaris
Hi Peeps,
Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out:
when you boot net install
It still asks you to select a language and locale, after you do this it kicks of an unattended install.
So my question is,... (5 Replies)
Discussion started by: callmebob
5 Replies
7. UNIX for Advanced & Expert Users
Hi,
where can i find documention on how to create a jumpstart system?
dori (2 Replies)
Discussion started by: dorilevy
2 Replies
8. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
9. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
10. UNIX for Dummies Questions & Answers
I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies
cfengine(8) System Manager's Manual cfengine(8)
NAME
cfrun - Execute remote cfagents
SYNOPSIS
/usr/sbin/cfrun [options]
DESCRIPTION
cfengine is a language based system specifically designed for testing and configuring unix-like systems attached to a TCP/IP network.
cfrun is a tool for executing one or more remote agents; it contacts the cfservd daemon running on a remote host, which (in turn) starts an
authorized agent. Cfrun cannot be used to send instructions to a remote agent, but it can be used to flag certain aspects to the agent's
existing policy for special attention..
The command line options for cfrun are slightly unusual. They are separated into three sections: options to the cfrun program, options to
the remote cfagent (with some security restrictions) and finally classes or flags to the remote agent.
EXAMPLES
cfrun specialhost1 specialhost2 -- --verbose -- solaris
In this example, we contact hosts specialhost1 specialhost2 by name, and ask them to execute cfagent with the --verbose flag, if the class
solaris is not defined.
cfrun specialhost1 --verbose -- -- solaris
In this example the verbose flag is sent to cfrun rather than to the remote agent. No options are sent to the remote agents. The class
specifier is sent to all the agents so that they may determine whether they fulfill the required class membership for execution.
The default behaviour is to execute cfagent serially on all hosts listed in the cfrun.hosts file.
FILES
cfrun read a configuration file cfrun.hosts which must contain a list of every potentially contactable host.
AUTHOR
Mark Burgess, Oslo University College
INFORMATION
http://www.cfengine.org
Maintenance Commands cfengine(8)