10 More Discussions You Might Find Interesting
1. Solaris
I've followed a few guides and have what appears to be a working jumpstart server. I can PXE boot a bare system, it gets an IP and launches the installer. However, it takes me to the screen:
SunOS Release 5.10 Version generic-147148-26 64 bit
Copyright (c) 1983, 2013, Oracle and/or its... (1 Reply)
Discussion started by: jnojr
1 Replies
2. Solaris
I 'm tryin to install a solaris server After all the system initialization & extraction of flash archive installation aborts with following error ..
Does anyone know what could be the issue for the same ?
Any help would be appreciated
Extracted 2205.05 MB ( 99% of 2205.54 MB... (6 Replies)
Discussion started by: fugitive
6 Replies
3. Solaris
I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created:
install_type
initial_install
system_type server
cluster SUNWCXall... (4 Replies)
Discussion started by: msarro
4 Replies
4. Solaris
I have a jumpstart client that is not requesting the tftp boot file. The rarp function is working, hostname and ip are set ok, but it hangs after that.
tcpdump output:
jumpstart-server:/var/lib/tftpboot# tcpdump -i eth1
tcpdump: verbose output suppressed, use -v or -vv for full protocol... (6 Replies)
Discussion started by: skitch
6 Replies
5. Solaris
I have created profile file for zfs root (flash) on a wanboot server when i try to validate the rules file with check i get following error .. i 'm not sure why i 'm getting this error .. can any one help me on this ?
# ./check
Validating rules...
Validating profile profile...
Error in... (0 Replies)
Discussion started by: fugitive
0 Replies
6. Solaris
Hi Peeps,
Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out:
when you boot net install
It still asks you to select a language and locale, after you do this it kicks of an unattended install.
So my question is,... (5 Replies)
Discussion started by: callmebob
5 Replies
7. UNIX for Advanced & Expert Users
Hi,
where can i find documention on how to create a jumpstart system?
dori (2 Replies)
Discussion started by: dorilevy
2 Replies
8. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
9. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
10. UNIX for Dummies Questions & Answers
I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies
rpc_listen(3ncs) rpc_listen(3ncs)
Name
rpc_listen - listen for and handle remote procedure call (RPC) packets (server only)
Syntax
#include <idl/c/rpc.h>
void rpc_$listen(max_calls, status)
unsigned long max_calls;
status_$t *status;
Arguments
max_calls This value indicates the maximum number of calls that the server is allowed to process concurrently. On ULTRIX systems,
this value should be 1; any other value is ignored and defaulted to one.
status The completion status. If the completion status returned in is equal to status_$ok , then the routine that supplied it was
successful.
Description
The routine dispatches incoming remote procedure call requests to manager procedures and returns the responses to the client. You must
issue or before you use This routine normally does not return. A return from this routine indicates either an irrecoverable error, or that
an call has been issued. If is equal to status_$ok , the assumption is that has occurred.
Examples
Listen for incoming remote procedure call requests.
rpc_$listen (1, &status);
Diagnostics
This section lists status codes for errors returned by this routine in
rpc_$not_in_call An internal error.
rpc_$you_crashed This error can occur if a server has crashed and restarted. A client RPC runtime library sends the error to the server
if the client makes a remote procedure call before the server crashes, then receives a response after the server
restarts.
rpc_$proto_error An internal protocol error.
rpc_$bad_pkt The server or client has received an ill-formed packet.
Files
See Also
intro(3ncs), rpc_shutdown(3ncs)
rpc_listen(3ncs)