10 More Discussions You Might Find Interesting
1. Solaris
I've followed a few guides and have what appears to be a working jumpstart server. I can PXE boot a bare system, it gets an IP and launches the installer. However, it takes me to the screen:
SunOS Release 5.10 Version generic-147148-26 64 bit
Copyright (c) 1983, 2013, Oracle and/or its... (1 Reply)
Discussion started by: jnojr
1 Replies
2. Solaris
I 'm tryin to install a solaris server After all the system initialization & extraction of flash archive installation aborts with following error ..
Does anyone know what could be the issue for the same ?
Any help would be appreciated
Extracted 2205.05 MB ( 99% of 2205.54 MB... (6 Replies)
Discussion started by: fugitive
6 Replies
3. Solaris
I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created:
install_type
initial_install
system_type server
cluster SUNWCXall... (4 Replies)
Discussion started by: msarro
4 Replies
4. Solaris
I have a jumpstart client that is not requesting the tftp boot file. The rarp function is working, hostname and ip are set ok, but it hangs after that.
tcpdump output:
jumpstart-server:/var/lib/tftpboot# tcpdump -i eth1
tcpdump: verbose output suppressed, use -v or -vv for full protocol... (6 Replies)
Discussion started by: skitch
6 Replies
5. Solaris
I have created profile file for zfs root (flash) on a wanboot server when i try to validate the rules file with check i get following error .. i 'm not sure why i 'm getting this error .. can any one help me on this ?
# ./check
Validating rules...
Validating profile profile...
Error in... (0 Replies)
Discussion started by: fugitive
0 Replies
6. Solaris
Hi Peeps,
Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out:
when you boot net install
It still asks you to select a language and locale, after you do this it kicks of an unattended install.
So my question is,... (5 Replies)
Discussion started by: callmebob
5 Replies
7. UNIX for Advanced & Expert Users
Hi,
where can i find documention on how to create a jumpstart system?
dori (2 Replies)
Discussion started by: dorilevy
2 Replies
8. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
9. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
10. UNIX for Dummies Questions & Answers
I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies
RUP(1) BSD General Commands Manual RUP(1)
NAME
rup -- remote status display
SYNOPSIS
rup [-dhlt] [host ...]
DESCRIPTION
rup displays a summary of the current system status of a particular host or all hosts on the local network. The output shows the current
time of day, how long the system has been up, and the load averages. The load average numbers give the number of jobs in the run queue aver-
aged over 1, 5 and 15 minutes.
The following options are available:
-d For each host, report what it's local time is. This is useful for checking time synchronization on a network.
-h Sort the display alphabetically by host name.
-l Sort the display by load average.
-t Sort the display by up time.
The rpc.rstatd(8) daemon must be running on the remote host for this command to work. rup uses an RPC protocol defined in
/usr/include/rpcsvc/rstat.x.
EXAMPLES
example% rup otherhost
otherhost up 6 days, 16:45, load average: 0.20, 0.23, 0.18
example%
DIAGNOSTICS
rup: RPC: Program not registered
The rpc.rstatd(8) daemon has not been started on the remote host.
rup: RPC: Timed out
A communication error occurred. Either the network is excessively congested, or the rpc.rstatd(8) daemon has terminated on the
remote host.
rup: RPC: Port mapper failure - RPC: Timed out
The remote host is not running the portmapper (see rpcbind(8)), and cannot accommodate any RPC-based services. The host may be down.
SEE ALSO
ruptime(1), rpc.rstatd(8), rpcbind(8)
HISTORY
The rup command appeared in SunOS.
BSD
June 7, 1993 BSD