I don't success configure solaris network,so I reinstall Solaris sol-10-u6-ga1-x86-dvd.iso,when installing,I configure following contents:
Code:
Networked: Yes
Use DHCP: No
Host name: universe
IP address: 10.18.18.188
System part of a subnet: Yes
Netmask: 255.255.255.0
Enable IPv6: Yes
Default Route: Specify one
Router IP Address: 10.18.18.1
After installed,I reboot Solars,this time I can success login and no error occur. Then I look up hosts file,it follows:
Code:
::1 localhost
127.0.0.1 localhost
10.18.18.188 universe loghost
#ifconfig -a
lo0:flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 15000 index 2
inet 10.18.18.188 netmask ffffff00 broadcast 10.18.18.255
lo0:flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
inet6 ::1/128
e1000g0: flags=2004841<UP,RUNNING,MULTICAST,DHCP.IPv6> mtu 1500 index 2
inet6 :fe80::20c:29ff:feec:14d0/10
#cat /etc/netmasks
10.18.18.0 255.255.255.0
#cat /etc/networks
loopback 127
arpanet 10 arp
#netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
--------------------------------------------------------------------------------
default 10.18.18.1 UG 1 0
10.0.0.0 10.18.18.188 U 1 20 e1000g0
224.0.0.0 10.18.18.188 U 1 0 e1000g0
127.0.0.1 127.0.0.1 UH 14 11561 lo0
#cat /etc/defaultrouter
10.18.18.1
#arp -a
Net to Media Table: IPv4
Device IP Address Mask Flag
e1000g0 universe 255.255.255.255 SPLA
e1000g0 224.0.0.0 240.0.0.0 SM
I can ping my own IP address
Code:
#ping 10.18.18.188
10.18.18.188 is alive
Then I ping gateway ip address
Code:
#ping 10.18.18.1
ICMP Host Unreachable from gateway universe (10.18.18.188)
for icmp from universe (10.18.18.188) to 10.18.18.1
Then I ping other machine
Code:
#ping 10.18.18.5
ICMP Host Unreachable from gateway universe (10.18.18.188)
for icmp from universe (10.18.18.188) to 10.18.18.5
But other machine can ping gateway and ping each other except this solaris 10 machine!!!
For example,other machine ip address is 10.18.18.5,it can ping gateway but it can't ping this solaris 10 machine!
Code:
#ping 10.18.18.1
10.18.18.1 is alive
#ping 10.18.18.5
10.18.18.5 is alive
#ping 10.18.18.188
ICMP Host Unreachable from gateway
Where wrong with solaris 10 machine? I am frustrated with it for several days! How to correct it?
Thanks
Last edited by Scott; 01-22-2011 at 08:51 AM..
Reason: Code tags, please...
Try:
dladm show-dev
dladm show-link
route show 10.18.18.1
netmask 255.255.255.0 for 10.18.18.188 correct ?
is 10.18.18.0/24 a vlan ? -> vlan tagging on the network switch port enabled ?
is the mac address of e1000g0 visible on the network switch port ?
network cable problem ? reconncet/exchange the cable, does e1000g1 work ?
is ip 10.18.18.188 already in use by another server ?
I would connect a known good machine to the same cable with the same network configuration as the Solaris 10 machine so you can be 100% certain whether or not its related to the Solaris machine or your network infrastructure.
If it is your network infrastructure I would check to see if you are using port security on the switch you are connected to (if so configure the switch with your Solaris 10 machines e1000g0 NIC's MAC address), that the port is in the correct vlan, and that the port on the switch is enabled.
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Hi all,
I got a Fujitsu P650 server running on Solaris 9 and we are going to re-install Solaris 10 . W have a build server in a different IP segment. So we setup a boot server and /etc/ethers and /etc/bootparams are all updated. When I issue
boot net -install,
I'm getting the following... (3 Replies)
Hi,
Need help for the network configuration on Solaris 10 5/8.
My NIC's dirver was loaded after Solaris installation and is configured using static ip address for a local network: 172.16.1.12
I have configured set of files as: /etc/hosts :
172.16.1.12 ls12
/etc/hostname.iprb0:... (7 Replies)
Hi,
I'm very new to Solaris world and istarted my learnign with a Blade T6320 Server.
I was trying to install Solaris 10.8 from a DVD image over the network.
But from the client(the machine which i want to install Solaris) when i tried boot net , i am getting a message like " cannto find... (5 Replies)
Hi,
i have installed solaris on virtual box in my desktop, i wanted to know how to make it network enabled(nated network). Nated network means it will use same IP as of my windows right? so is it possible that using the same IP i can enable the network on this virtual box.
Thanks in advance. (3 Replies)
I have installed solaris x86 on a standalone PC. Now I have connected a LAN cable to it. What do I do next for further configuration or to access internet from that solaris machine? (16 Replies)
I have a solaris x86 box that ive been having trouble getting on my network, anyone know a good guide that can take me through it step by step? (1 Reply)