I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created:
After this, the install proceeds without too much problem. After the install reboots the server, I receive the following messages:
I have rebooted to the OS install cd and run fsck, and there are no errors.
Here's my vfstab file:
When i try to remount using
I receive an error stating:
That /dev/rdsk/c1t0d0s0 is not ufs. Except it is ufs!
I'm kind of lost. Any suggestions? This is a new system so I'm strongly considering just nuking the install and trying again.
what kind of raid adapter are you using? i need the part number. certain controller need a newer version of solaris for driver support... if an older solaris version is used, you need to patch the driver into the minikernel...
The minimum Solaris operating system is Solaris 10 5/08 (SPARC) or Solaris 10 8/07 (x86).
so your solaris version should be ok. my first try would be a clean install from DVD and check if everything is ok. if this works, it should be a jumpstart (wrong config...) problem.
also make sure this is true:
Quote:
Use Cable Option SEDX9SA2Z to connect the HBA to the T5220 Disk Backplane.
Last edited by DukeNuke2; 01-11-2011 at 07:58 PM..
I've followed a few guides and have what appears to be a working jumpstart server. I can PXE boot a bare system, it gets an IP and launches the installer. However, it takes me to the screen:
SunOS Release 5.10 Version generic-147148-26 64 bit
Copyright (c) 1983, 2013, Oracle and/or its... (1 Reply)
I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems.
Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86?
Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
I 'm tryin to install a solaris server After all the system initialization & extraction of flash archive installation aborts with following error ..
Does anyone know what could be the issue for the same ?
Any help would be appreciated
Extracted 2205.05 MB ( 99% of 2205.54 MB... (6 Replies)
I have a jumpstart client that is not requesting the tftp boot file. The rarp function is working, hostname and ip are set ok, but it hangs after that.
tcpdump output:
jumpstart-server:/var/lib/tftpboot# tcpdump -i eth1
tcpdump: verbose output suppressed, use -v or -vv for full protocol... (6 Replies)
I have created profile file for zfs root (flash) on a wanboot server when i try to validate the rules file with check i get following error .. i 'm not sure why i 'm getting this error .. can any one help me on this ?
# ./check
Validating rules...
Validating profile profile...
Error in... (0 Replies)
Hello everyone,
I tried to install solaris 10 using the command # boot net - install.
I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following:
... (7 Replies)
Hi all ,
I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows :
cleaning up preexisting install client "XXXXXXX"
removing XXXXXXXfrom bootparams
removing /etc/bootparams, since it is... (14 Replies)
I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)