Solaris 19 10/09 ipv6 interface configuration


 
Thread Tools Search this Thread
Operating Systems Solaris Solaris 19 10/09 ipv6 interface configuration
# 1  
Old 11-04-2010
Question Solaris 19 10/09 ipv6 interface configuration

Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however, when I restart the server, the IP address was not preserved, only preserves the link local address.
Thanks for your help and welcome your comments.

Pablo

Last edited by DukeNuke2; 11-04-2010 at 04:15 PM..
# 2  
Old 11-04-2010
read a little further in the admin guide... there should be a part about a file called "/etc/hostname6.<your_nic>".
This User Gave Thanks to DukeNuke2 For This Post:
# 3  
Old 11-06-2010
This User Gave Thanks to jld For This Post:
# 4  
Old 11-08-2010
Thanks for the help, the problem was in a router that modified during my test.
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Red Hat

About the apache for ipv6 configuration

I am running apache 2 on centos 7 which is running ipv4 , now I would like to enable it to support ipv6 , would advise what I need to change to Adding IPv6 support to the server ? or nothing need to do ? the existing vhosts is as below . <VirtualHost *:80> ServerAdmin xxx.com.hk " "... (2 Replies)
Discussion started by: ust3
2 Replies

2. Solaris

How to assign IPv4 and IPv6 addresses with same interface?

Hello dears how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies

3. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

4. IP Networking

IPv6 address block assign/associate with an interface

Hello all, I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack. One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies

5. Linux

Help Me: How to set ARP stale time interval on linux platform for Ipv6 interface

Hi, Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ? I have tried increasing the variable gc_stale_time but that doesnt work. Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies

6. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies

7. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

8. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

9. Red Hat

wireless interface timeout configuration

Hello, I have a small desktop running RedHat 5. Depending where I'm at, it connects to the network by a wireless interface or a wired interface. If I'm in an are where there is no wireless network, the box hangs on boot up. It will not timeout and move on. It just hangs. Is there a timeout... (0 Replies)
Discussion started by: garskoci
0 Replies

10. Solaris

Network interface configuration

Dears, i follow this to configure Network interface for my PC O/S : Unix Sun Solaris vi /etc/hostname.bge0 and write my ip vi /etc/netmasks and write my subnetmask vi /etc/defautrouter and write my gatwey vi /etc/resolv.conf and write my DNS after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies
Login or Register to Ask a Question