9 More Discussions You Might Find Interesting
1. Linux
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
2. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
3. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
4. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
5. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
6. Solaris
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies
7. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
8. Solaris
Hi there,
I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server.
*I have re-compiled the linux kernel t support ufs fstype with ro mount support.
filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies
9. BSD
Hello All,
How can i mount ext3 and Fat partition in FreeBSD 6.0 (0 Replies)
Discussion started by: jaibw
0 Replies
ISCSI.CONF(5) File Formats Manual ISCSI.CONF(5)
NAME
iscsi.conf - iSCSI Target and LUN configuration
SYNOPSIS
/etc/iscsi.conf
DESCRIPTION
This manual page describes the format of the /etc/iscsi.conf file. This file is a simple text file that iscsid(8) uses to locate iSCSI tar-
get devices and LUNs. Comments are marked by lines beginning with '#'.
Available entries include:
DiscoveryAddress=<address>
IP address or hostname to use for target discovery. A TCP port number may be specified by appending a colon followed by the port
number. This entry must start in the first column, and must not contain any whitespace.
TargetIpAddr=<address>
A synonym for DiscoveryAddress.
Username=<user>
Specify the authentication user. If this entry precedes all DiscoveryAddress entries, it serves as the default. If this entry is
indented under a DiscoveryAddress entry, it specifies the user for all targets discovered at that IP address.
Password=<pass>
Specify the authentication password for the previously listed iSCSI If this entry precedes all DiscoveryAddress entries, it serves
as the default. If this entry is indented under a DiscoveryAddress entry, it specifies the user for all targets discovered at that
IP address.
EXAMPLE
# set the default user and password
Username=alice
Password=nty57nbe
# targets at this address will use the default Username and Password
DiscoveryAddress=192.168.10.94
# targets at this address will use the Username and Password below
DiscoveryAddress=192.168.10.95
Username=beatrice
Password=93fdgc20
NOTES
The iSCSI initiator drivers, README files, and example configuration files are available on the Linux-iSCSI homepage at:
http://linux-iscsi.sourceforge.com <http://linux-iscsi.sourceforge.com>
FILES
/etc/iscsi.conf
iSCSI Target and LUN configuration
SEE ALSO
iscsid(8)
$Revision: 1.9 $ $Date: 2002/09/19 20:00:32 $ ISCSI.CONF(5)