9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. HP-UX
Hi All
I have a blade BL860c running on a C7000 chassis, in which is connected to a NetApp, so lately I am having I/O issues, and dmesg as well as syslog.log is reporting the following:
/dev/vg01/lvol2 file system file data error in dev/block 0/55892768
Page I/O error occurred while paging... (2 Replies)
Discussion started by: fretagi
2 Replies
3. UNIX for Dummies Questions & Answers
I have scheduled couple of shell scripts to run using 'at' command.
The o/p of at -l is:
$ at -l
1320904800.a Thu Nov 10 01:00:00 2011
1320894000.a Wed Nov 9 22:00:00 2011
1320876000.a Wed Nov 9 17:00:00 2011
$ uname -a
SunOS dc2prcrptetl2 5.9 Generic_122300-54 sun4u sparc... (2 Replies)
Discussion started by: superparticle
2 Replies
4. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
5. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
8. HP-UX
Hi All,
I've recently been given an HP-UX Visualise J5600 to look after which runs our backup management software - it's connected to the network via 2 Gigabit Fibre channel cables.
Any ideas which command will give me the full connection details for those interfaces (and/or any others... (3 Replies)
Discussion started by: geralex
3 Replies
9. UNIX for Dummies Questions & Answers
On a sparc solaris 8 host running sunone webserver 6 I would like to limit the http requests that can be used when port 80 is accessed. We currently have http/1.0 enabled.
For example I would like to remove the http request DELETE.
Regards,
BLP (1 Reply)
Discussion started by: blp001
1 Replies