Solaris 10 - QLogic 4060C iSCSI adapter

Solaris 10 - QLogic 4060C iSCSI adapter - multipathed (MPxIO)

10 More Discussions You Might Find Interesting

1. Solaris

Qlogic 10G Ethernet adapter not working

Hi Community, i have one issue with 10 fiber ethernet adapter. here is my details: root@new-bpel.example.com #dladm show-dev bge0 link: unknown speed: 0 Mbps duplex: unknown bge1 link: up speed: 1000 Mbps duplex: full qlge2 link:...

2. Solaris

Solaris OS having issue accessing LUN from Qlogic swich

Hi Community, I am facing one issue related storage accessing from solaris 10 machine(M5000). it was working fine then we shifted to another site. the only change on that site is FC switch. The issue i am facing is from solaris machine i can able to see the LUN, it;s only a test lun of 30...

3. Solaris

Solaris 11 iscsi chap auth

hi to all i've done that steps, but i was not completely successful: sudo pkg install group/feature/storage-server sudo svcadm enable stmf sudo zfs create -V 1g rpool/LUN1 sudo stmfadm create-lu /dev/zvol/rdsk/rpool/LUN1 sudo stmfadm list-lu ...

4. Solaris

Solaris 10 + mpxio Path

Hi, I have an Oracle/Sun T3-2 Server with a duel SAS controller Fujitsu DX60 array attached. I have 2 x SAS HBA's in the T3-2. One HBA cabled to CM0 and one HBA cabled to CM1 of the array. The array is setup with one RAID GROUP and one VOLUME and one LUN In Solaris I can see one device...

5. Solaris

solaris turn off multipath mpxio

Im not able to turn the multipath off on the solaris s10 X86...since im on FC boot.. if i disable multipath , from /kernel/drv/iscsi.conf then im not able to boot the machine.:wall: Is there any other go or any suggestions .

6. Solaris

Solaris 10 MPXIO doesn't recover path failure

I have been running some tests with solaris mpxio, dual-pathed to HDS SAN storage. When I take a path offline, Solaris recognised this and a path is shown as offline in luxadm display <device>. However, it does not recover on reinstatement of the path until I run cfgadm -al. Any ideas? Phil

7. UNIX for Dummies Questions & Answers

How to change ethernet cable of iscsi initiator (iscsi client)?

how to change ethernet cable of iscsi initiator (iscsi client)

8. UNIX for Advanced & Expert Users

Solaris 10 10/09 u8, iSCSI and SUN Trunking

I am running Solaris 10 on a V490. I have Dell EqualLogic SAN attached. I would like to take full advantage of the iSCSI initiator. I have a primary network interface and IP addresses for all four SAN ports. Since the four ports are SUN GigaSwift (legacy), I cannot utilize dladm, so I downloaded...

9. Solaris

iscsi device on solaris 10 (x64)

Hello! I have several disks discovered using iscsi protocol. There disks are represented in OS like c2txd0 . logs: Is it possible to change drive path, for example, from c2t6d0 to c2t7d0? It's important for me because I have to install oracle RAC on RAW devices. NIck

10. Solaris

Solaris 10 10/08 sparc + iSCSI

hi, I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work. Thanks, Prashant.

LEARN ABOUT NETBSD

iscsi-target

ISCSI-TARGET(8) 					    BSD System Manager's Manual 					   ISCSI-TARGET(8)

NAME

     iscsi-target -- service remote iSCSI requests

SYNOPSIS

     iscsi-target [-46DV] [-b block length] [-f configuration file] [-p port number] [-s maximum number of sessions] [-t target name]
		  [-v verbose arg]

DESCRIPTION

     iscsi-target is the server for iSCSI requests from iSCSI initiators.  iscsi-target listens for discovery and login requests on the required
     port, and responds to those requests appropriately.

     Options and operands available for iscsi-target:

     -4      iscsi-target will listen for IPv4 connections, and respond back using IPv4.  This is the default address family.

     -6      iscsi-target will listen for IPv6 connections, and respond back using IPv6.

     -b blocksize
	     Specify the underlying block size for iSCSI storage which will be served.	The possible sizes are: 512, 1024, 2048, and 4096 bytes,
	     with the default being 512 bytes.

     -D      When this option is specified, iscsi-target will not detach itself from the controlling tty, and will not become a daemon.  This can
	     be useful for debugging purposes.

     -f configfile
	     Use the named file as the configuration file.  The default file can be found in /etc/iscsi/targets.  See targets(5) for more informa-
	     tion.

     -p port number
	     Use the port number provided as the argument as the port on which to listen for iSCSI service requests from initiators.

     -s maximum number of sessions
	     Allow the maximum number of sessions to be initiated when connecting to the target.

     -t filename
	     The target name (as it appears to the iSCSI initiator) can be specified using this flag.

     -V      iscsi-target will print the utility name and version number, and the address for bug reports, and then exit.

     -v argument
	     The amount of information shown can be varied by using this command.  Possible values of argument are net to show network-related
	     information, iscsi to show iSCSI protocol-related information, scsi to show SCSI protocol information, and all to show information
	     from all of the above arguments.

FILES

     /etc/iscsi/targets 	the list of exported storage
     /var/run/iscsi-target.pid	the PID of the currently running iscsi-target

SEE ALSO

     targets(5)

HISTORY

     The iscsi-target utility first appeared in NetBSD 4.0.

BSD
								   May 27, 2006 							       BSD

Solaris