10 More Discussions You Might Find Interesting
1. Solaris
Hi
Please can you help me on replacing or removing a faulty disk drive on a SUN NETRA X4250server with 4 internal drives only.
the format comand show me the following:
format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c0t0d0 <drive type unknown>
... (9 Replies)
Discussion started by: fretagi
9 Replies
2. AIX
Iam new to AIX
I am unable varyonvg on the vios,some of the disk are reported as harware failure.
I am going to replace the disk,Please tell me how to remove the disk without any corruption in the VG
lspv -l hdiskx also didn't work (0 Replies)
Discussion started by: roayaix
0 Replies
3. Solaris
I have an oldish Solaris 10 system (SunFire x4240), which due to a recent heating event in the server room, lost it's system disk.
I have rsync backups of all the other (data) disks, but apparently I do not have a backup of /. :-( I can start the machine up in failsafe mode, but running fsck on... (4 Replies)
Discussion started by: jj5406
4 Replies
4. Red Hat
Hi Masters,
How to find out the failed disk in redhat linux (OR)
How to decalare whether our hard disk goes bad ?
My option is:
dmesg | grep "failed"
check in /var/log/messages with the kernel error.
Please corrrect me if im wrong.
And also i heard "smartctl" command. But it's... (2 Replies)
Discussion started by: abhay1983
2 Replies
5. UNIX for Advanced & Expert Users
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
6. Linux
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
7. Boot Loaders
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
8. Solaris
-bash-3.00# zpool detach zonepool c1t1d0
cannot detach c1t1d0: only applicable to mirror and replacing vdevs
-bash-3.00# zpool remove zonepool c1t1d0
cannot remove c1t1d0: only inactive hot spares, cache, top-level, or log devices can be removed
-bash-3.00# zpool offline zonepool c1t1d0... (3 Replies)
Discussion started by: LittleLebowski
3 Replies
9. Solaris
Dear all
Please can any one explain me how to replace failed disk in Solaris 10.
Please tell me the step by step procedure. (9 Replies)
Discussion started by: suneelieg
9 Replies
10. UNIX for Advanced & Expert Users
My WS boot disk has failed so when i want to boot system (by OK boot -s or Ok boot disk0 ) i get these mesgs:
disk read error
boot :can not find misc/sparc9v/krtld
boot:error loading interperetor (misc/sparc9v/krtld)
Elf64 read error.
boot failed.
although it's probed ,finally i try... (1 Reply)
Discussion started by: nikk
1 Replies