10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi everyone;
I need to create a shell script for full and incremental backup purposes. for incremental backup only for one folder (test1) located in /home/test1 syntax below works fine and have no problem: tar -cvf /home/backup/backup-0.tar.gz -g /home/test1/test.snar /home/test Problem is here... (5 Replies)
Discussion started by: momed131
5 Replies
2. Shell Programming and Scripting
HI all, im new to shell scripting. need your guidence for my script. i wrote one script and is attached here
Im explaining the requirement of script.
AIM: Shell script to run automatically as per scheduled and backup few network devices configurations. Script will contain a set of commands... (4 Replies)
Discussion started by: saichand1985
4 Replies
3. Solaris
Hello
I am new to solaris samba. After configuring samba through swat I can see the the machine listed under windows workgroup computers. when selected it shows the shared directories, But when trying to connect to shares shows a error network path not found.
At the same time solaris network... (5 Replies)
Discussion started by: kc2dws
5 Replies
4. AIX
I have an aix server, it is not a VIO server or client. I need to check if it has multi-path driver installed, how to check it? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
5. Solaris
Hi there
Now, Ive always support servers that used multi path software with dual cards, e.g. powerpath (emc ) / MPXIO. I got asked a question today, that if a solaris 8/9/10 host had 2 HBA cards, but no multipathing software, what would happen ?? Does the HBA card with the highest id on the... (2 Replies)
Discussion started by: sbk1972
2 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ? :confused: (2 Replies)
Discussion started by: mik
2 Replies
7. Red Hat
Hi all,
i need to backup files on network from RHEL 4 machine
tape drive is installed on solaris 10 machine and want ot use this
using
# tar cv /myfiles |ssh -l myuser myhost 'buffer -o /dev/rmt/0 "
to backup these file but getting getting error " sh buffer not found '
even "buffer-1.19-1"... (2 Replies)
Discussion started by: ajays
2 Replies
8. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
9. Shell Programming and Scripting
Dear All,
I have a problem in knowing ..how the network path is represented in the unix ..I need sample in shell script to find whether the given path is in network or not . (0 Replies)
Discussion started by: yessowmya
0 Replies
10. UNIX for Advanced & Expert Users
Hi all,
I have 4 unix servers (2 of them are OpenBSD 2.8, and the other 2 RedHat) Is there any way i can backup those servers through the network to a hard drive. I have checked NDMP though. Is there any free software network backup software or smth like that? All comments and suggestions are... (3 Replies)
Discussion started by: solvman
3 Replies
ADSL-SETUP(8) System Manager's Manual ADSL-SETUP(8)
NAME
adsl-setup - Shell script to configure Roaring Penguin PPPoE client
SYNOPSIS
adsl-setup
DESCRIPTION
adsl-setup is a shell script which prompts you for various pieces of information and sets up an /etc/sysconfig/network-scripts/ifcfg-ppp0
configuration script for the adsl-start, adsl-stop and adsl-connect scripts.
AUTHOR
adsl-setup was written by David F. Skoll <dfs@roaringpenguin.com>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.
SEE ALSO
pppoe(8), adsl-start(8), adsl-stop(8), adsl-connect(8), pppd(8), pppoe.conf(5), adsl-status(8), pppoe-sniff(8), pppoe-relay(8), pppoe-
server(8)
4th Berkeley Distribution 21 February 2000 ADSL-SETUP(8)