Network card installation issue

10 More Discussions You Might Find Interesting

1. Linux

Network card module installation

Hi, I am using Red Hat 9.0 and it does not have the inbuilt driver module for my onboard lan card (RTL 8169). I downloaded the module (file - r8169-6.017.00.tar.bz2 and even r8169-6.015.00.tar.bz2), but when try to install it it says r8169.h , r8169_n.c , Makefile etc are...

2. Red Hat

Network card module installation

3. SuSE

Network card naming issue

I have a Sun server running SuSE with 2 network cards, the cards naming is eth0-to-eth3 for the first card, and eth4-eth7 for the second one, I've replace the second card and I got naming issue: I got eth4, eth5, eth7, eth8 I mean the system doesn't see eth6 so it took eth7 instead, is there a way...

4. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks !

5. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

7. Solaris

installation of Solaris: installation bypasses network config.

hello solaris friends, I've tried installing Sun Solaris 10.0, but everytime it seems to bypass the network config. screen that looks similar to this...here's the url: http://www.hup.hu/old/images/hup/Solaris/Sol10beta7/9.png I'm able to install it all the way through but I get no...

8. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

9. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

LEARN ABOUT REDHAT

axnet_cs

AXNET_CS(4)						     Kernel Interfaces Manual						       AXNET_CS(4)

NAME

       axnet_cs - Asix AX88190 chipset PCMCIA Ethernet Driver

SYNOPSIS

       insmod axnet_cs.o [pc_debug=n] [irq_list=i,j,...]

DESCRIPTION

       Axnet_cs  is  a driver for PCMCIA ethernet cards based on the Asix AX88190 chipset.  These cards are mostly NE2000 compatible but have sev-
       eral bugs that are sufficiently tricky to work around that a separate driver was deemed necessary.  When this driver is bound to a card, it
       allocates  the  next  available	ethernet  device (eth0..eth#).	This device name will be reported in the kernel log file, and passed on to
       cardmgr(8).

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

DIAGNOSTICS

       axnet_cs: this is not an AX88190 card!
	      Indicates that this card is probably a normal NE2000 compatible card, which requires the pcnet_cs driver.

       eth#: interrupt(s) dropped!
	      Indicates that the driver did not receive an interrupt notification for some reason.  The driver will poll the card (with a signifi-
	      cant performance penalty) if the problem persists.  The most likely cause is an interrupt conflict and/or host bridge  configuration
	      problem.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5).

pcmcia-cs							2001/08/17 12:51:58						       AXNET_CS(4)

Solaris