Network card installation issue

10 More Discussions You Might Find Interesting

1. Linux

Network card module installation

Hi, I am using Red Hat 9.0 and it does not have the inbuilt driver module for my onboard lan card (RTL 8169). I downloaded the module (file - r8169-6.017.00.tar.bz2 and even r8169-6.015.00.tar.bz2), but when try to install it it says r8169.h , r8169_n.c , Makefile etc are...

2. Red Hat

Network card module installation

3. SuSE

Network card naming issue

I have a Sun server running SuSE with 2 network cards, the cards naming is eth0-to-eth3 for the first card, and eth4-eth7 for the second one, I've replace the second card and I got naming issue: I got eth4, eth5, eth7, eth8 I mean the system doesn't see eth6 so it took eth7 instead, is there a way...

4. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks !

5. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

7. Solaris

installation of Solaris: installation bypasses network config.

hello solaris friends, I've tried installing Sun Solaris 10.0, but everytime it seems to bypass the network config. screen that looks similar to this...here's the url: http://www.hup.hu/old/images/hup/Solaris/Sol10beta7/9.png I'm able to install it all the way through but I get no...

8. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

9. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

LEARN ABOUT CENTOS

opensc-tool

OPENSC-TOOL(1)							   OpenSC Tools 						    OPENSC-TOOL(1)

NAME

       opensc-tool - generic smart card utility

SYNOPSIS

       opensc-tool [OPTIONS]

DESCRIPTION

       The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
       sending arbitrary APDU commands to a card.

OPTIONS

       --atr, -a
	   Print the Answer To Reset (ATR) of the card. Output is in hex byte format

       --card-driver driver, -c driver
	   Use the given card driver. The default is auto-detected.

       --info, -i
	   Print information about OpenSC, such as version and enabled components.

       --list-drivers, -D
	   List all installed card drivers.

       --list-files, -f
	   Recursively list all files stored on card.

       --list-readers, -l
	   List all configured readers.

       --name, -n
	   Print the name of the inserted card (driver).

       --reader num, -r num
	   Use the given reader number. The default is 0, the first reader in the system.

       --send-apdu apdu, -s apdu
	   Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....

       --serial
	   Print the card serial number (normally the ICCSN). Output is in hex byte format

       --verbose, -v
	   Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.

       --wait, -w
	   Wait for a card to be inserted.

SEE ALSO

       opensc-explorer(1)

opensc								    06/17/2014							    OPENSC-TOOL(1)

Solaris