9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have two physical interface connected to solaris box.
1. e1000g1
2. e1000g2
I have added these interfaced under a same IPMP group "IPMP1"
After that I have configured a test address for e1000g1 like below
ifconfig e1000g1 addif <ip-address> netmask + broadcast + -failover... (1 Reply)
Discussion started by: praveensharma21
1 Replies
2. AIX
On all our lpars we have our main interface set up and a backup network interface. On a number of our lpars those connections go to a down state for no apparent reason. They are still attached but they show up as "*en1" in netstat. Has anyone else come across this issue or know why an... (4 Replies)
Discussion started by: bsewen
4 Replies
3. Solaris
Hi all
i had two interface
ce0 and ce5
but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it?
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies
4. Solaris
Hi,
I've a problem when try to detach nic e1000g1.
IPMP configuration:
# ifconfig -a
...cut...
e1000g1: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 7
inet 0.0.0.0 netmask 0
ether 0:c:29:67:16:ef
e1000g2: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4>... (3 Replies)
Discussion started by: gxmsgx
3 Replies
5. Solaris
can anyone help me fix this? what command should I use to bring them back to "TRUE"?
Interface Speed Duplex Autoneg
--------- ----- ------ -------
ce0 100 Mbit/s FULL FALSE
ce5 100 Mbit/s FULL ... (3 Replies)
Discussion started by: uuontario
3 Replies
6. Solaris
Hi,
I have recently configured IPMP on a Solaris 10 server. Everything was working ok when I removed the network cable from interface ce0. The floating IP failed over to ce1.
Unfortunately when I plugged the network cable back into ce0 about 2 minutes later it did not come back up. Is... (11 Replies)
Discussion started by: sparcman
11 Replies
7. UNIX for Dummies Questions & Answers
hello friends
i am using x86 pc i can install solaris o/s but nic card is not deceting.
i am not able see in file called /etc/path_to_inst. i did /touch reconfigu and
devfsadm also. i used external nic card also realtech 8169d am using gigabyte mother board 775. (0 Replies)
Discussion started by: manoj123
0 Replies
8. Solaris
Hi,
I have a problem with a server disconnecting from the network.
This is a SUN box with dual NIC's running Solaris 8.
We have a Nokia router that routes traffic but it's virtual address doesn't respond to pings. When the SUN box sends out a ping, if nothing comes back it will shut down... (5 Replies)
Discussion started by: m_smith
5 Replies
9. UNIX for Dummies Questions & Answers
i have just installed suse 8.1 on a third computer which has an Asus p4s8x with onboard NIC and sound. now, on install suse detected everything automatically with no probelm, however upon reboot the sound failed to load as well as the network card. /dev/eth* doesnt exist. i looked in the bios and... (2 Replies)
Discussion started by: norsk hedensk
2 Replies
