10 More Discussions You Might Find Interesting
1. Programming
I use a binary name (ie polo) it gets some parameter , so for debugging normally i do this :
i wrote script for watchdog my app (polo) and check every second if it's not running then start it , the problem is , if my app , remain in state of segmentation fault for a while (ie 15 ... (6 Replies)
Discussion started by: pooyair
6 Replies
2. Emergency UNIX and Linux Support
Hi guys!
I need to upgrade the fw version of some T2000 servers, but unfortunately the image downloaded from the Oracle does not work...it seems that the image is not supported on the platform..
bash-3.00$ uname -a
SunOS adm01 5.10 Generic_141414-07 sun4v sparc SUNW,Sun-Fire-T200... (5 Replies)
Discussion started by: cecco16
5 Replies
3. Solaris
This may be a stupid question, but I don't want to take any chances.
I have a Sun T2000 in production. I want to run the "resetsc" command on the ALOM controller to active an IP address change. Will resetting ALOM affect the running OS?
Thanks (2 Replies)
Discussion started by: soliberus
2 Replies
4. Solaris
Hi all,
First post so be gentile :)
It's my first time installing Solaris on T2000 server.
I have 2 72GB HD's on it.
After configuring HW raid and running raidctl command I get this output:
bash-3.00# raidctl -l c0t0d0
Volume Size Stripe Status Cache RAID
... (2 Replies)
Discussion started by: Obi-Wan
2 Replies
5. Solaris
Hi All,
I recently had issues with my new T2000 server. I purchased a new mainboard and swapped the CPU and DIMMs to the new board. Now when i power on the server im unable to do so. I get the following error:
‘SC Alert: Host system poweron failed due to fault at MB/FF_POK.'
When i do... (2 Replies)
Discussion started by: Caully
2 Replies
6. Solaris
New to the boards here so please bear with me!
I have a T2000 server with Solaris 10 installed on it. Disk 0 is the only disk currently being used, as I do NOT have a RAID set up. Disk 1 is just sitting there looking pretty.
I'd like to set up a mirrored RAID in order to fully utilize both... (5 Replies)
Discussion started by: phi148
5 Replies
7. Solaris
Hi, a couple of T2000 servers did not show the component status and the output was too short. There was a patch that needed to be installed. I also updated to the latest recommended patch cluster and OBP patch.
After reboot/restart of picl, it worked ok for a couple of weeks. Then suddenly it went... (12 Replies)
Discussion started by: incredible
12 Replies
8. Solaris
Hi,
I have a root with hardware RAID on c0t0d0 and c0t2d0. I would like to set the boot device sequence in OBP for both hdds.
I have checked in ls -l /dev/rdsk/ for the path of c0t2d0 but it does not exist. Can anyone shed some lights on this?
AVAILABLE DISK SELECTIONS:
0.... (12 Replies)
Discussion started by: honmin
12 Replies
9. Solaris
Hi everyone,
I am having a problem when running devfsadm. We have many T2000, but on one of them, that is connected to our SAN, devfsadm reports no new disks. If a reconfiguration reboot is done, the system reports the new disk. But only with a reboot. We have Solaris10 installed and Veritas... (13 Replies)
Discussion started by: jfotop
13 Replies
10. Solaris
I have an issue with DNS on a solaris t2000
When I set up the zones there was an issue with the /etc/resolv.conf, I had made a typo in my DNS server.
I only noticed this after creating my new zones.
I have corrected this in the global zone and I am now able to ping and nslookup inthe... (2 Replies)
Discussion started by: james dewitt
2 Replies