Faster firmware for the T5240

10 More Discussions You Might Find Interesting

1. Solaris

Using a Modem on a T5-2 or a T5240

Hi Folks, Just a quick question - hopefully! I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes...

2. Solaris

Question: # of ldoms on T5240 with 2 T2 US 8 core

I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure?

3. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ...

4. Solaris

Disable multithreading option on T5240

Hi Gurus Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core Regards

5. Solaris

Bizarre Sun T5240 behavior

Hi - I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages: WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed WARNING: nxge3 : nxge_alloc_rx_buf_dma:...

6. Solaris

ufsrestore T5240

Hi Friends we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there? Regards Rajasekar

7. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS

8. Solaris

T5240 netmgmt port not blinking

I was trying to configure the netmgmt from the serial and set commitpending to true. However, the netmgmt port is not up and blinking. I tried to connect using my notebook directly to the netmgmt port and am not able to ping as well. Previouly i was doing the firmware upgrade using the webconsole....

9. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on...

10. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try

LEARN ABOUT SUSE

atmel_fwl

ATMEL_FWL(8)						      System Manager's Manual						      ATMEL_FWL(8)

NAME

       atmel_fwl - Load firmware into Atmel at76c50x wireless networking chips.

SYNOPSIS

       atmel_fwl <interface> /path/to/firmware

DESCRIPTION

       atmel_fwl loads firmware images for Atmel at76c50x series wireless networking chips into the Linux driver for same.

       Note  that this utility is not normally necessary, since the driver will automatically load the correct firmware image via the hotplug sys-
       tem. Atmel_fwl is provided for applications where use of the hotplug system may not be desirable.

       atmel_fwl should be run after the interface has been created (after card insertion, in the case of PCMCIA cards) but before it  is  brought
       up by running ifconfig.

NOTES

       Note that there are two versions of many of the firmware images, the second one with the suffix "-wpa". These are later releases from Atmel
       which support WPA privacy. They are only usable by versions of the driver greater than 0.9. Be sure not to use the "-wpa" one  unless  your
       in-kernel driver code is version 0.9 or better. Sadly, as of version 0.9, the in-kernel driver does not actually support the setting of WPA
       passphrases.

       The firmware images are usually installed in /usr/lib/hotplug/firmware.

       The status of the driver, including its firmware loading, is available in /proc/driver/atmel

FILES

       /usr/lib/hotplug/firmware

       /proc/driver/atmel

SEE ALSO

       iwconfig(8), ifconfig(8),

AUTHOR

       This manual page was written by Simon Kelley <simon@thekelleys.org.uk>.

																      ATMEL_FWL(8)

Solaris BigAdmin RSS