10 More Discussions You Might Find Interesting
1. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
2. Solaris
I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure? (5 Replies)
Discussion started by: Iftikhar Barrie
5 Replies
3. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
4. Solaris
Hi Gurus
Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core
Regards (3 Replies)
Discussion started by: amity
3 Replies
5. Solaris
Hi -
I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages:
WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed
WARNING: nxge3 : nxge_alloc_rx_buf_dma:... (2 Replies)
Discussion started by: pyroman
2 Replies
6. Solaris
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies
7. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
8. Solaris
I was trying to configure the netmgmt from the serial and set commitpending to true. However, the netmgmt port is not up and blinking.
I tried to connect using my notebook directly to the netmgmt port and am not able to ping as well. Previouly i was doing the firmware upgrade using the webconsole.... (20 Replies)
Discussion started by: incredible
20 Replies
9. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
10. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
URTWNFW(4) BSD Kernel Interfaces Manual URTWNFW(4)
NAME
urtwnfw -- Firmware Module for Realtek Wireless driver
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device urtwnfw
This will include three firmware images inside the kernel. If you want to pick only the firmware image for your network adapter choose one
of the following:
device urtwn-rtl8192cfwT
device urtwn-rtl8192cfwU
device urtwn-rtl8188eufw
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
urtwn-rtl8192cfwT_load="YES"
urtwn-rtl8192cfwU_load="YES"
urtwn-rtl8188eufw_load="YES"
DESCRIPTION
This module provides access to firmware sets for the Realtek RTL8188CUS, RTL8188CE-VAU, RTL8188EUS, RTL8188RU and RTL8192CU chip based USB
WiFi adapters. It may be statically linked into the kernel, or loaded as a module.
For the loaded firmware to be enabled for use the license at /usr/share/doc/legal/realtek must be agreed to by adding the following line to
loader.conf(5):
legal.realtek.license_ack=1
FILES
/usr/share/doc/legal/realtek urtwnfw firmware license
SEE ALSO
urtwn(4), firmware(9)
BSD
April 25, 2014 BSD