Faster firmware for the T5240

10 More Discussions You Might Find Interesting

1. Solaris

Using a Modem on a T5-2 or a T5240

Hi Folks, Just a quick question - hopefully! I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes...

2. Solaris

Question: # of ldoms on T5240 with 2 T2 US 8 core

I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure?

3. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ...

4. Solaris

Disable multithreading option on T5240

Hi Gurus Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core Regards

5. Solaris

Bizarre Sun T5240 behavior

Hi - I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages: WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed WARNING: nxge3 : nxge_alloc_rx_buf_dma:...

6. Solaris

ufsrestore T5240

Hi Friends we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there? Regards Rajasekar

7. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS

8. Solaris

T5240 netmgmt port not blinking

I was trying to configure the netmgmt from the serial and set commitpending to true. However, the netmgmt port is not up and blinking. I tried to connect using my notebook directly to the netmgmt port and am not able to ping as well. Previouly i was doing the firmware upgrade using the webconsole....

9. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on...

10. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try

LEARN ABOUT MOJAVE

firmwarepasswd

FIRMWAREPASSWD(8)					    BSD System Manager's Manual 					 FIRMWAREPASSWD(8)

NAME

     firmwarepasswd -- tool for setting and removing firmware passwords on a system

SYNOPSIS

     firmwarepasswd [-setpasswd] [-setmode mode] [-mode] [-check] [-delete] [-verify] [-unlockseed] [-h]

DESCRIPTION

     The firmwarepasswd command is used to add or remove firmware passwords from a system as well as check status and other options.  The
     firmwarepasswd command requires root privileges to run.

     A list of flags and their descriptions:

     -setpasswd
	     Prompts to add a new firmware password or change and existing password if one exists.

     -setmode mode
	     Set the mode to "command" or "full".  "Command" will prompt for the firmware password if the user attempts to boot from a different
	     volume.  "Full" will prompt on every startup (not recommended).

     -mode   Displays the current mode if one is set.

     -check  Displays whether or not a firmware password is set.

     -delete
	     Prompts for password and clears both password and the mode if correct.

     -verify
	     Prompts for password and displays success if correct.

     -unlockseed
	     Generates a firmware password recovery key.  Note: Machine must be stable for this command to generate a valid seed.  No pending
	     changes that need a restart.  NOTE: Seed is only valid until the next time a firmware password command runs.

     -h      Displays a list of all the commands available in the firmwarepasswd tool, with explanatory information.

FILES

     /usr/sbin/firmwarepasswd

OS X
								   April 9, 2014							      OS X

Solaris BigAdmin RSS