10 More Discussions You Might Find Interesting
1. Solaris
Hi Folks,
Just a quick question - hopefully!
I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes... (3 Replies)
Discussion started by: gull04
3 Replies
2. Solaris
I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure? (5 Replies)
Discussion started by: Iftikhar Barrie
5 Replies
3. Solaris
Hi !
I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before.
I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl.
... (2 Replies)
Discussion started by: delavega
2 Replies
4. Solaris
Hi Gurus
Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core
Regards (3 Replies)
Discussion started by: amity
3 Replies
5. Solaris
Hi -
I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages:
WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed
WARNING: nxge3 : nxge_alloc_rx_buf_dma:... (2 Replies)
Discussion started by: pyroman
2 Replies
6. Solaris
Hi Friends
we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there?
Regards
Rajasekar (5 Replies)
Discussion started by: rajasekg
5 Replies
7. Solaris
Hi,
We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions.
RJS (4 Replies)
Discussion started by: rajasekg
4 Replies
8. Solaris
I was trying to configure the netmgmt from the serial and set commitpending to true. However, the netmgmt port is not up and blinking.
I tried to connect using my notebook directly to the netmgmt port and am not able to ping as well. Previouly i was doing the firmware upgrade using the webconsole.... (20 Replies)
Discussion started by: incredible
20 Replies
9. Solaris
its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file.
getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies
10. Solaris
Setting up a T5240 with two disks c1t0d0 and c1t1d0.
I am trying to use raidctl but when I issue.
raidctl -l
I get
Controller 1
Disk: 0.0.0
Disk: 0.1.0
So I try
raidctl -c '0.0.0 0.1.0' -r 1 1
and I get "Array in use."
I try (4 Replies)
Discussion started by: photon
4 Replies
I2M19058(1) GNU Info I2M19058(1)
NAME
ift-extract.info - ift-extract.info
Built-in iSight firmware extractor and patcher
ift-extract extract the Built-in iSight firmware from Apple driver and patch it to avoid some bugs in it. The firmware is then ready to get
loaded into the chip using ift-load.
* Menu:
Finding the Apple driver: see "Driver"
Command line options: see "Options"
See also "Copying"
1 Finding the Apple driver
ift-extract extract Built-in iSight firmware from Apple iSight driver. This driver is located at
/System/Library/Extensions/IOUSBFamily.kext/Contents/PlugIns/AppleUSBVideoSupport.kext/Contents/MacOS/AppleUSBVideoSupport on your Mac OS X
root partition.
There is several version of this driver depending on driver version or host architecture (PowerPC or x86). Thus, ift-extract must determine
know the variant of the driver in order to properly extract the firmware.
Any AppleUSBVideoSupport file starting with those shipped with iMac G5 iSight must work. If not, please report unknown AppleUSBVideoSupport
at bugreport mail address with machine type and OS X version.
2 Command line options
`-a' `--apple-driver' Apple driver filename where to extract the firmware.
`-d' `--output-directory' The directory where to output the firmware. Defaults to /lib/firmware.
`-f' `--output-filename' The output firmware name. Defaults to isight.fw
`-?' `--help' Shows option help and quit.
Since ift-extract defaults to output the firmware to /lib/firmware/isight.fw, ensure you have the right to do so.
3 Copying
isight-firmware-tools is a project developped by A~Xtienne Bersac based on the work of Ronald S. Bultje, Johannes Berg and Ivan N. Zlatev.
This manual has been written by A~Xtienne Bersac.
Copyright (C) 2007 A~Xtienne Bersac <bersace@gmail.com>
perl v5.14.2 2012-01-09 I2M19058(1)