This Sun BluePrints document describes using RAID 6 (a RAID algorithm that is gaining popularity and can be cheaper to implement than RAID 1+0 and more reliable than RAID 5) on the Sun StorageTek 6140 array.
Hi,
I have a question about Sun StorageTek Common Array Manager (CAM): What is the concept of 'host'? Is it the hostname of the server that has access to the managed array? If so, can I use its IP instead of its hostname?
I've found a 'host' under CAM called XYZ (See below). In our... (7 Replies)
In Sun manuals, I didn't find how to backup Sun StorageTek Common Array Manager's configuration. Is there a way to do it like backing up Brocade switch configuration? CAM is under Solaris 10.
Thank you in advance! (0 Replies)
Hi!
I have Sun StorageTek 2540 FC array and CAM works very slowly - I can wait for software response even more than 2 minutes... I run this software on Windows machine with Firefox Web Browser but speed is terrible... How can I make it works at least a little bit faster?.. (2 Replies)
Hello,
Wondering if anyone can help me with mounting a file share from my Sun T2000 server running Solaris 10 to my connected 2530 disk array?
I believe I've connected the disk array correctly and I have created a volume on the array using the filesystem (Sun_SAM-FS, RAID-5).
The T2000... (15 Replies)
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey.
Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)?
One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
IIR(4) BSD Kernel Interfaces Manual IIR(4)NAME
iir -- Intel Integrated RAID controller and ICP Vortex driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device scbus
device iir
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
iir_load="YES"
DESCRIPTION
The iir driver claims to interface with the Intel integrated RAID controller cards, and all versions of the ICP Vortex controllers (including
FC).
HARDWARE
Controllers supported by the iir driver include:
o Intel RAID Controller SRCMR
o Intel Server RAID Controller U3-l (SRCU31a)
o Intel Server RAID Controller U3-1L (SRCU31La)
o Intel Server RAID Controller U3-2 (SRCU32)
o All past and future releases of Intel and ICP RAID Controllers.
o Intel RAID Controller SRCU21 (discontinued)
o Intel RAID Controller SRCU31 (older revision, not compatible)
o Intel RAID Controller SRCU31L (older revision, not compatible)
The SRCU31 and SRCU31L can be updated via a firmware update available from Intel.
SEE ALSO cam(4), pass(4), xpt(4), camcontrol(8)AUTHORS
The iir driver is supported and maintained by Achim Leubner <Achim_Leubner@adaptec.com>.
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org> and is based on information supplied by the driver authors and the website
of Mike Smith <msmith@FreeBSD.org>.
BSD August 8, 2004 BSD
