10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
There are two servers which needs to be connected via the port number 1521 from a remote server.
This is the port config in the first server : L28tstream1 :
# netstat -tulpn | grep 1521
tcp 0 0 10.67.26.183:1521 0.0.0.0:* LISTEN ... (2 Replies)
Discussion started by: anaigini45
2 Replies
2. IP Networking
Hi,
I have read some forum theads about the open and close ports. some points are clear and it is not working on my machine or something am i missing?
I have commented out a port /etc/services, one application uses
then when i use the telnet <hostname> <port_blocked> it shows connected..... (1 Reply)
Discussion started by: balamv
1 Replies
3. UNIX for Dummies Questions & Answers
just a quick question:
a. whats the simplest command to check open port and the corresponding services?
example:
bash-2.05# netstat -an | grep LISTEN
*.199 *.* 0 0 49152 0 LISTEN
*.8989 *.* 0 0 49152 ... (1 Reply)
Discussion started by: lhareigh890
1 Replies
4. Solaris
hi guys,
may i know the exact steps to open a port in solaris.i have some rough idea - which is adding the port number in /etc/services.
but i am not sure the correct conventions, steps or any other steps.
kindly advise.thanks guys ! (1 Reply)
Discussion started by: cromohawk
1 Replies
5. Solaris
Hello,
I have a number of Solaris 8 Sun servers that have open ports that I cannot identify. I see some with 1013-1023 (which are reserved ports according to the IANA. Lsof does not identify these. I rebooted the server and they went off, but this morning I saw they were all back on again. Any... (1 Reply)
Discussion started by: csgonan
1 Replies
6. UNIX for Dummies Questions & Answers
Hello,
I have a number of Solaris 8 Sun servers that have open ports that I cannot identify. I see some with 1012-1020 (which are reserved ports according to the IANA. Lsof does not identify these. One server has all these on and one server just has 1017.
*.1023 ... (3 Replies)
Discussion started by: csross
3 Replies
7. AIX
Hi Every body,
What is the command on AIX 5.2 that can be used to get all open ports? (2 Replies)
Discussion started by: aldowsary
2 Replies
8. Shell Programming and Scripting
Hello, i need a script (bash type maybe?..), which would check open ports on 127.0.0.1 and then compare open ports with "registered/allowed" port list and try to kill the program who uses unregistered ports. It would be great that script would be started lets say every 5 or 10 minutes.
You see i... (2 Replies)
Discussion started by: MorchiuS
2 Replies
9. Linux
how can i open ports i need in red hat server vs root access ? (7 Replies)
Discussion started by: Sirius
7 Replies
10. Cybersecurity
/* Linux Slackware */
Nmap shows the following ports open on the gateway.
21/tcp ftp
22/tcp ssh
23/tcp telnet
25/tcp smtp
37/tcp time
80/tcp http
113/tcp auth
515/tcp printer
587/tcp submission
1024/tcp kdm
6000/tcp x11
-------------------------------
i would like to close as... (10 Replies)
Discussion started by: LowOrderBit
10 Replies
iscc(7) Miscellaneous Information Manual iscc(7)
NAME
iscc - serial communications interface
SYNOPSIS
controller iscc0 at isa0
DESCRIPTION
An onboard Zilog 8530 DUART provides AXPvme-based Single Board Computers with console (CON) and auxiliary (AUX) serial communications
ports. Both serial communications ports can operate at baud rates from B50 to B38400, excluding B134 (see tty(7)).
On AXPvme Single Board Computers configured with a graphics head as the system console, the CON serial communications port (/dev/tty01) is
available for use by application programs as an additional communications port.
In the absence of a graphics head, the CON serial communications port (/dev/console) becomes the system console. When used as the serial
system console, the CON serial communications port always operates at 9600 BPS, 8-bits, and no parity.
Regardless of system console, the AUX serial communications port (/dev/tty00) is always available for use by application programs.
RESTRICTIONS
Data communications equipment attached to the CON serial communications port must be set to 9600 BPS, 8-bits, no parity when configured as
the serial system console. The iscc terminal driver enforces this restriction.
No modem control is supported for either the CON or AUX serial communications ports.
FILES
console terminal local terminal local terminal
RELATED INFORMATION
console(7), devio(7), tty(7), MAKEDEV(8) delim off
iscc(7)