Kernel Conference Australia: Panel Discussion on ZFS

4 More Discussions You Might Find Interesting

1. Solaris

Solaris 11.2 dump device "kernel without ZFS metadata"

I've never seen this, is it normal for 11.2? Anyway to change it back to dumping metadata or is this simply an overly verbose message I may ignore? kernel without ZFS metadata

2. AIX

Australia NSW DST

Hello. Our application is running on AIX box located in NSW , Australia. As DST starts on Oct 28th - Do you know IF AIX boxes have auto updates of day light saving times? IF not , how to do it? IF yes, where can I verify it? Thank you!

3. Shell Programming and Scripting

DST Change For Australia

Hello , We are investigating an issue from a customer from Western Australia related to DST change on 25 th March. The customer in Australia has the below settings for Time Zone. The System is Solaris 9. TZ=Australia/NSW CMASK=022 We are trying to reproduce the problem in our local...

4. Shell Programming and Scripting

confused in australia

hi! i have a lot of files (800+) (in windows format - i.e. they have spaces in the filename) that i need to copy to disk... if i write a for loop to ls the files and copy it fails as the file it trys to read is just the 1st part of the file (which of course doesnt exist)... i dont want to...

LEARN ABOUT FREEBSD

zfsboot

ZFSBOOT(8)						    BSD System Manager's Manual 						ZFSBOOT(8)

NAME

     zfsboot -- bootcode for ZFS on BIOS-based computers

DESCRIPTION

     zfsboot is used on BIOS-based computers to boot from a filesystem in a ZFS pool.  zfsboot is installed in two parts on a disk or a partition
     used by a ZFS pool.  The first part, a single-sector starter boot block, is installed at the beginning of the disk or partition.  The second
     part, a main boot block, is installed at a special offset within the disk or partition.  Both areas are reserved by the ZFS on-disk specifi-
     cation for boot use.  If zfsboot is installed in a partition, then that partition should be made bootable using appropriate configuration and
     boot blocks described in boot(8).

BOOTING

     The zfsboot boot process is very similar to that of gptzfsboot(8).  One significant difference is that zfsboot does not currently support the
     GPT partitioning scheme.  Thus only whole disks and MBR partitions, traditionally referred to as slices, are probed for ZFS disk labels.  See
     the BUGS section in gptzfsboot(8) for some limitations of the MBR scheme support.

USAGE

     zfsboot supports all the same prompt and configuration file arguments as gptzfsboot(8).

FILES

     /boot/zfsboot  boot code binary
     /boot.config   parameters for the boot block (optional)
     /boot/config   alternative parameters for the boot block (optional)

EXAMPLES

     zfsboot is typically installed using dd(1).  To install zfsboot on the ada0 drive:

	   dd if=/boot/zfsboot of=/dev/ada0 count=1
	   dd if=/boot/zfsboot of=/dev/ada0 iseek=1 oseek=1024

     If the drive is currently in use, the GEOM safety will prevent writes and must be disabled before running the above commands:

	   sysctl kern.geom.debugflags=0x10

     zfsboot can also be installed in an MBR slice:

	   gpart create -s mbr ada0
	   gpart add -t freebsd ada0
	   gpart create -s BSD ada0s1
	   gpart bootcode -b /boot/boot0 ada0
	   gpart set -a active -i 1 ada0
	   dd if=/boot/zfsboot of=/dev/ada0s1 count=1
	   dd if=/boot/zfsboot of=/dev/ada0s1 iseek=1 oseek=1024

     Note that commands to create and populate a pool are not shown in the example above.

SEE ALSO

     dd(1), boot.config(5), boot(8), gptzfsboot(8), loader(8), zfsloader(8), zpool(8)

HISTORY

     zfsboot appeared in FreeBSD 7.3.

AUTHORS

     This manual page was written by Andriy Gapon <avg@FreeBSD.org>.

BUGS

     Installing zfsboot with dd(1) is a hack.  ZFS needs a command to properly install zfsboot onto a ZFS-controlled disk or partition.

BSD
								September 15, 2014							       BSD

Solaris BigAdmin RSS