9 More Discussions You Might Find Interesting
1. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
2. Red Hat
I have managed to install Broadcom BCM43228 Wireless adapter on a laptop running CentOS 5.9 using instructions at:
wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
I had the problem "Error for wireless request "Set Encode" (8B2A): SET failed on device... mentioned on the same page and solved... (0 Replies)
Discussion started by: cooltoad
0 Replies
3. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
4. Solaris
hi everyone... this is my first post here
please help me with this..as iam new to solaris
i have installed solaris 10 on virtual box.. and am not able to connect to the internet ..
is there anyway i can get connect to the net..
please help me step by step if possible...
thanks in... (1 Reply)
Discussion started by: yrajendergoud
1 Replies
5. UNIX for Dummies Questions & Answers
I just installed a fork of opensolaris, and I really like it.
I would hate going back to Ubuntu, But one issue, I cannot get my Dell Wireless 1450 Wireless USB Adapter working.
On Ubuntu 10.4 I just installed nonfree firmware, but I guess it doesn't work that way on Solaris, any help would be... (5 Replies)
Discussion started by: Stormos
5 Replies
6. IP Networking
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies
7. UNIX Desktop Questions & Answers
I have backtrack 3 installed in my laptop. Using ndiswrapper for broadcom wirless driver. It connect on startup easily .. but problem is when it starts KDE or Flux it gets disconnectd..
how to solve this issue?
thanks a lot (0 Replies)
Discussion started by: nizammoidu
0 Replies
8. IP Networking
Hi,
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies
9. Cybersecurity
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
WIRELESS(7) Linux Programmer's Manual WIRELESS(7)
NAME
wireless - Wireless Tools and Wireless Extensions
SYNOPSIS
iwconfig
iwpriv -a
DESCRIPTION
The Wireless Extensions is an API allowing you manipulate Wireless LAN networking interfaces. It is composed of a variety of tools and
configuration files. It is documented in more detail in the Linux Wireless LAN Howto.
The Wireless Tools are used to change the configuration of wireless LAN networking interfaces on the fly, to get their current configura-
tion, to get statistics and diagnose them. They are described in their own man page, see below for references.
Wireless configuration is specific to each Linux distribution. This man page will contain in the future the configuration procedure for a
few common distributions. For the time being, check the file DISTRIBUTIONS.txt included with the Wireless Tools package.
DEBIAN 3.0
In Debian 3.0 (and later) you can configure wireless LAN networking devices using the network configuration tool ifupdown(8).
File : /etc/network/interfaces
Form : wireless-<function> <value>
wireless-essid Home
wireless-mode Ad-Hoc
See also :
/etc/network/if-pre-up.d/wireless-tools
/usr/share/doc/wireless-tools/README.Debian
SuSE 8.0
SuSE 8.0 (and later) has integrated wireless configuration in their network scripts.
Tool : Yast2
File : /etc/sysconfig/network/wireless
/etc/sysconfig/network/ifcfg-*
Form : WIRELESS_<function>=<value>
WIRELESS_ESSID="Home"
WIRELESS_MODE=Ad-Hoc
See also :
man ifup
info scpm
ORIGINAL PCMCIA SCRIPTS
If you are using the original configuration scripts from the Pcmcia package, you can use this method.
File : /etc/pcmcia/wireless.opts
Form : *,*,*,*)
ESSID="Home"
MODE="Ad-Hoc"
;;
See also :
/etc/pcmcia/wireless
File PCMCIA.txt part of Wireless Tools package
AUTHOR
Jean Tourrilhes - jt@hpl.hp.com
http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/
SEE ALSO
iwconfig(8), iwlist(8), iwspy(8), iwpriv(8), iwevent(8).
wireless-tools 4 March 2004 WIRELESS(7)