This script will check the status of a Sun HW Raid configured with raidctl and report errors via logger and mailNOTE: This script only applies to raid volumes on Solaris 10 8/07 (aka update 4) and newer. The raidctl command changed with that version.
Sorry if this is the wrong forum
Searching for Saas Monitor service which monitor my servers which are sitting in different providers .
This monitor tool will take as less CPU as possible , and will send info about the server to main Dashboard.
The info I need is CPU / RAM / my servers status (... (1 Reply)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Hi,
I need to write a directory monitor, i.e. a korn shell script which would
Report changes to the directory contents, like:
added file1,
deleted file2,
updated file3 ,
created subdir (optional)...
There is no specific file pattern.
So far I have written a little script... (1 Reply)
We use Sun Volume manager to mirror root disks and other local disks...
Is there any script to monitor raid status across all machines send output thru email?
Help is appreciated.
Thanks. (1 Reply)
MPT(4) BSD Kernel Interfaces Manual MPT(4)NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device mpt
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mpt_load="YES"
DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers.
HARDWARE
The following controllers are supported by the mpt driver:
o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI)
o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA)
o LSI Logic FC909 (1Gb/s Fibre Channel)
o LSI Logic FC909A (Dual 1Gb/s Fibre Channel)
o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel)
o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel)
o LSI Logic FC949X (Dual 4Gb/s Fibre Channel)
o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express)
The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including:
o Dell PowerEdge 1750 thru 2850
o IBM eServer xSeries 335
These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports.
The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both
SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at
best.
The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the
FC949ES card.
This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the
LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required.
SEE ALSO cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8)
LSI Logic Website, http://www.lsilogic.com/.
HISTORY
The mpt driver first appeared in FreeBSD 4.6.
AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>.
Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements.
BUGS BSD May 13, 2010 BSD