Sun Fire X Servers - ILOM Serial Console Configuration (Linux)
(I created the wiki page on BigAdmin describing how to configure the ILOM serial port for serial console access, similar to how you can do this on SPARC based servers) Configuring the ILOM SP serial console allows you to have an additional "lightweight" method of accessing a Linux console. This involves a few configuration steps in the ILOM SP and configuring GRUB to to provide the serial port as an additional output console.
Hi Oracle Hardware Specialists,
I have shutdown a Sun Fire X2200 server running Solaris 10 x86 to single user mode to experiment some backup commands using Web based Sun embedded Lights Out Manager Redirection to open up a console session. However, it is not possible to copy & past text with... (7 Replies)
Have a T5220 with Oracle SN stickers on outside with one SN, but the ILOM shows a different SN (from another server). It seems this is a issue with T5220's (a co-worker ran into similar problem with 2 of his servers, he just had the ILOM's swapped).
Anyone know the command to change the ILOM... (3 Replies)
Hi,
I need to install solaris remotely via the ILOM port on a x4170 box, and I have downloaded the Solaris 11 for x86 - text install image and burned it on a DVD.
When I boot the box, it's showing the boot_archive loading percentage on the SP console, but when it's done and start the interactive... (0 Replies)
Is it possible to set the information that shows in the cli banner when you login to the ILOM? In addition, after I set the hostname of the ILOM, how do I check it? (2 Replies)
Hello Folks,
I am having trouble to login to rsc or serial console of V890.
The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Hi,
I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?
Thanks,
Vineet (4 Replies)
ports(7) Miscellaneous Information Manual ports(7)NAME
ports, port_names - Device (tty and lp) names for serial and parallel ports
SYNOPSIS
Default Serial Ports:
/dev/tty00
/dev/tty01 (not present on a single-port system)
Parallel Port:
/dev/lp0
DESCRIPTION
AlphaStation and AlphaServer systems provide one or two 9-pin serial communication ports. These ports are usually labelled 1 (COMM1) and 2
(COMM2), but they may be identified by different icons. Using the appropriate serial cable and terminator, you can connect a serial
printer, external modem, or character-cell terminal to a serial port. Most AlphaStation and AlphaServer systems also provide one parallel
port, for use with a parallel printer.
When you add a device to your system, the installation documentation may instruct you to map the device pathname to the port. These
devices are located in the /dev directory.
For serial-line ports, the two default device pathnames are: This pathname always maps to 1, COMM1, the lowest port number, an icon for a
terminal console, or the only serial port (on a single-port system). This pathname always maps to 2, COMM2, the next numbered port, or (if
one serial port is labeled with an icon for a terminal console) the remaining serial port.
If your system hardware has been extended to include additional serial ports, the pathnames /dev/tty02, /dev/tty03, and so forth, may also
be available to you. However, most systems have only /dev/tty00 and /dev/tty01 as the device pathnames for serial ports.
The one parallel port on an AlphaStation or AlphaServer may be labeled with the word printer or a printer icon. On some systems, the paral-
lel port may not be labeled. The device pathname for the parallel port is /dev/lp0. Currently, Tru64 UNIX does not fully support parallel
printers, so fewer devices are connected to this port as compared to serial ports.
If you are connecting a terminal console to your system, it must be connected to the serial port mapped to /dev/tty00. For other serial
devices, it does not matter which of the serial ports you choose for the connection. For example, suppose you are setting up a system that
has two serial ports, labeled 1 and 2. You intend to use a serial-line terminal rather than a workstation monitor as the system console and
also want to connect a serial-line printer to the system. In this case, you must connect the terminal to the port labeled 1 (with the
device pathname /dev/tty00). Therefore, you must connect the printer to the remaining port labeled 2 (with the device pathname /dev/tty01).
If, for the same type of system, you intend to use a workstation monitor as the system console, it does not matter which serial port you
use for a serial-line printer or modem. In other words, you can connect the printer to either port 1 (with pathname /dev/tty00) or port 2
(with pathname /dev/tty01). When prompted to enter a /dev/tty** pathname by the lprsetup script or the Print configuration tool in the CDE
Application Manager, you would specify /dev/tty00 if you connected the printer to port 1 or /dev/tty01 if you connected the printer to port
2.
See the System Administration manual for more information on setting up consoles (including remote consoles) and printers. See the
modem(7) reference page for more information on setting up modems.
SEE ALSO
Commands: lprsetup(8)
Devices: ace(7), modem(7)
System Administration delim off
ports(7)