10 More Discussions You Might Find Interesting
1. Linux
Hi all,
I am using an F5 LTM Load balancer VM. Its network config is as follows:
eth0 Link encap:Ethernet HWaddr 00:50:56:01:01:FA
inet addr:192.168.2.104 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::250:56ff:fe01:1fa/64 Scope:Link
UP... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
2. Shell Programming and Scripting
Hey guys, I want to use a a quick bash script/command to determine what network interface is connected to the internet so I can pipe it out to become a variable, in order so the user does not have to manually type it in each time or have to 'hardcode' the variable into the script.
I know about... (6 Replies)
Discussion started by: 3therk1ll
6 Replies
3. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
4. UNIX for Dummies Questions & Answers
Hi All,
How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies
5. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
8. IP Networking
Hi,
ifconfig -a return:
eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A
inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0
... (5 Replies)
Discussion started by: djbuly
5 Replies
9. Solaris
Hi Community,
I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output:
# ifconfig hme0 <ip_address> netmask <mask> plumb
#ifconfig: plumb: hme0: no such interface
I've the same thing with dhcp service.
could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies
10. Solaris
Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies
bttape(8) System Manager's Manual bttape(8)
NAME
bttape - Bootable Tape Creation utility
SYNOPSIS
/usr/sbin/sysman bttape [-ui cui | gui [-display displayname] ]
OPTIONS
Specifies the user interface to be invoked. The choices are: Invokes the command line interface. Invokes the graphical user interface.
Specific command line options that will be used to interact.
DESCRIPTION
The Bootable Tape Creation utility is used by the system administrator to create a bootable system image, that consists of a standalone
kernel and copies of specified file systems. This standalone kernel is known as a miniroot and contains the requirements for a minimal
operating system.
In the event of a crash recovery, the system administrator can boot and restore file systems from the bootable system image by using the
btextract(8) utility.
During the creation of the bootable system image, you are prompted for the kernel name, the tape device, and the type of miniroot file sys-
tem, that is, a memory file system or disk partition to be used for the bootable tape image.
You are also prompted for the pathname of the Miniroot Append file, which lets you specify which additional files or directories should be
included in the miniroot. The size of the Miniroot Append file should not exceed 360KB. You are also prompted for the pathname of the File
System Backup File which defines which file systems are backed up to tape. Each line of this file specifies one file system by its device
name, mount point, and type of file system. The bttape(8) utility provides for the creation and modification of these files.
The bttape command has two user interface options: Graphical user interface (GUI) Command line interface (CUI)
Online help is available for the bttape application. To get help, select any Help button or use the Help pull-down menu.
Running the Graphical User Interface Option:
The bttape application can be invoked from:
The CDE Application Manager Application Group: System_Admin System Admin SubGroup: Storage_Management
To start bttape from the command line, enter: /usr/sbin/sysman bttape -gui
Running the Command Line Interface Option:
To start the bttape command line interface, enter the following command from the terminal: /usr/sbin/sysman bttape -ui cui [cuioptions]
RESTRICTIONS
You must have the appropriate privileges to use this application.
FILES
Bootable Tape Creation utility Help Volume Managment interface files User-defined file User-defined file to designate which file systems to
back up
SEE ALSO
Commands: X(1X), btcreate(8), btextract(8)
System Administration
bttape(8)
10-15-2008
