The NEC2 post-processor (necpp) is post-processor for the graphic files produced by NEC2, the antenna analyzer. It plots the results in various ways, including gain and SWR. Antenna designers and radio amateurs should find this useful. License: GNU General Public License (GPL) Changes:
This version was recompiled with FORTRAN in Debian release 4.0. The math-coprocessor is used.
Guys...
Hows it going???
I have been going through the hardware spec of IBM system p systems.. and here i am confused
for IBM Power 520 Express it says
Processor cores:
One, two or four 64-bit 4.2 GHz POWER6 with AltiVec™ SIMD and Hardware Decimal Floating-Point acceleration
... (1 Reply)
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
So here is a snippet from an analysis of test runs conducted in a robot experiment in the form of a table:
-----------------------------
| TN | TE | PA | PB |
-----------------------------
| Y | N | - | B |
| N | Y | A | B |
TN = Is the target... (1 Reply)
processor_sets(4) Kernel Interfaces Manual processor_sets(4)NAME
processor_sets - Collections of processors
DESCRIPTION
A processor set is a collection of processors. When a processor set is first created, it does not contain any processors. You can add
processors to a processor set, remove processors from a processor set, and also destroy the processor set. In addition, you can assign
specific processes to a processor set.
When the system is booted, all its processors are assigned to the default processor set. Each processor in a system can be a member of
only one processor set at one time.
In addition, when you create a process, it is assigned to a processor set. Unless you indicate a specific processor set, a process is
assigned to the default processor set. A process can execute only on an processor that is included in the processor set to which the
process is assigned. If you assign a process to an empty processor set, it will not execute until a processor is assigned to the processor
set or until the process is assigned to another processor set.
Use the pset_create command or the create_pset function to create a processor set. When you first create a processor set, it does not con-
tain any processors.
Use the pset_assign_cpu command or the assign_cpu_to_pset function to assign processors to a specific processor set. When you assign a
processor to a specific processor set, the processor is removed from its current processor set.
Use the pset_destroy command or the destroy_pset function to destroy a processor set. Processors that belong to a destroyed processor set
are assigned to the default processor set.
Use the pset_assign_pid command or the assign_pid_to_pset function to assign a process to a specific processor set. In addition, you can
request that a process has exclusive access to a processor set. If a process has exclusive access to a processor set, no other process is
able to use that processor set. If a process has exclusive access to a processor set, that access will be cleared automatically when the
process exits. Note that if a process is already assigned to a processor set, a request for exclusive access to that processor set will be
denied.
Use the pset_info command to display the status of each processor set on the system as well as the status of each processor.
You must be root to create and destroy processor sets and to assign a processor to a processor set. Processor set creation and destruction
and processor assignments to processor sets are logged in the /var/adm/wtmp file.
FILES
/var/adm/wtmp
RELATED INFORMATION
Commands: pset_create(1), pset_destroy(1), pset_info(1), pset_assign_pid(1), pset_assign_cpu(1), runon(1), psrinfo(1), psradm(8)
Functions: assign_pid_to_pset(3), assign_cpu_to_pset(3), create_pset(3), destroy_pset(3) delim off
processor_sets(4)