We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
When the system is powered on The kernel of External Raid controller starts up first and after POST , it gives the message No drives found.
Next the Internal controller bios comes up and shows the 4 hard disks.
Now when we press Ctrl+A and get in to the Raid Controller Bios the internal controller shows all the 4 hard disks.
However the external controller does not show any drives at all.
Once we boot into Solaris or Linux and run Commn Array manager ( in out-of-band mode) it shows the 5 hard disks and allows us to create volumes. But after that
when we tried to create file systems it just hangs. We tried to create a small filesystem of 1GB. Even that is not going through in both Solaris and Linux.
is it possible to assign value to an array variable from an external file?? if yes then how??
I am using below code but its not working.
#!bin/bash
myarray < file_name
echo ${mayarray} (6 Replies)
Hi,
Trying to setup mediawiki on a system but having problems configuring mysql:
CC=/usr/bin ./configure
checking build system type... powerpc-ibm-aix6.1.0.0
checking host system type... powerpc-ibm-aix6.1.0.0
checking target system type... powerpc-ibm-aix6.1.0.0
checking for a... (9 Replies)
Hello,
I am running a bash script under linux which first defines an CA-array like
j=0
num1=120.00
num2=10.00
until
do
CA='echo $num1 + $j*$num2'
j=$
done
within the later awk section of this same script I want to read data from a file. If the value of the second column is... (3 Replies)
Hello All:
I am trying to configure a J4200 disk array. I am a newbie.
1. I have installed CAM (Common Array Manager).
2. Upgraded the firmware.
3. Registered the array.
a. As per the user guide I should see a sas-domian which I don't.
b. I did not find instructions on how to setup a... (0 Replies)
HI,
I am facing these two errors while configuring snmp can any body guide me.
vi /var/log/snmpd.log
Error opening specified endpoint "udp:161"
Server Exiting with code 1
i also tried
bash-3.00# netstat -a | grep snm
*.snmpd Idle
bash-3.00# lsof -i :161
bash: lsof: command not... (2 Replies)
Hi All
I am new to Apache and AIX and trying to configure Subversion tool in IBM machine with AIX 5.3.Apache is required for client to connect to Subversion Server with http protocol.
1.Installed Apache 2.2.11 and its dependencies via RPM
2.Configured httpd.conf file.
3.Started "httpd"... (1 Reply)
Hello there,
I installed Ajaxterm on my Ubuntu 9.04 machine, and it's running ok if I use :
http://localhost:8022/ in my browser it works. The problem is that I wanted to be able to access it from somewhere else through the internet. I've read all the documentation and help that is available for... (1 Reply)
Hi all
Ive got a v440 with an external T3 RAID in a dual bus configuration. I need to add an additional JBOD extension to the disk array via two VDCH cables.
Now, can I do this as the server is live ? Can I just plug the two cables in, switch on the additional extension ? Will this cause... (1 Reply)
Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten
Unable to get NIC working
Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)