10 More Discussions You Might Find Interesting
1. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
2. Shell Programming and Scripting
is it possible to assign value to an array variable from an external file?? if yes then how??
I am using below code but its not working.
#!bin/bash
myarray < file_name
echo ${mayarray} (6 Replies)
Discussion started by: mukulverma2408
6 Replies
3. AIX
Hi,
Trying to setup mediawiki on a system but having problems configuring mysql:
CC=/usr/bin ./configure
checking build system type... powerpc-ibm-aix6.1.0.0
checking host system type... powerpc-ibm-aix6.1.0.0
checking target system type... powerpc-ibm-aix6.1.0.0
checking for a... (9 Replies)
Discussion started by: vpundit
9 Replies
4. Shell Programming and Scripting
Hello,
I am running a bash script under linux which first defines an CA-array like
j=0
num1=120.00
num2=10.00
until
do
CA='echo $num1 + $j*$num2'
j=$
done
within the later awk section of this same script I want to read data from a file. If the value of the second column is... (3 Replies)
Discussion started by: MotAah
3 Replies
5. Solaris
Hello All:
I am trying to configure a J4200 disk array. I am a newbie.
1. I have installed CAM (Common Array Manager).
2. Upgraded the firmware.
3. Registered the array.
a. As per the user guide I should see a sas-domian which I don't.
b. I did not find instructions on how to setup a... (0 Replies)
Discussion started by: pingmeback
0 Replies
6. Infrastructure Monitoring
HI,
I am facing these two errors while configuring snmp can any body guide me.
vi /var/log/snmpd.log
Error opening specified endpoint "udp:161"
Server Exiting with code 1
i also tried
bash-3.00# netstat -a | grep snm
*.snmpd Idle
bash-3.00# lsof -i :161
bash: lsof: command not... (2 Replies)
Discussion started by: nir1785
2 Replies
7. AIX
Hi All
I am new to Apache and AIX and trying to configure Subversion tool in IBM machine with AIX 5.3.Apache is required for client to connect to Subversion Server with http protocol.
1.Installed Apache 2.2.11 and its dependencies via RPM
2.Configured httpd.conf file.
3.Started "httpd"... (1 Reply)
Discussion started by: rajivdp
1 Replies
8. UNIX for Dummies Questions & Answers
Hello there,
I installed Ajaxterm on my Ubuntu 9.04 machine, and it's running ok if I use :
http://localhost:8022/ in my browser it works. The problem is that I wanted to be able to access it from somewhere else through the internet. I've read all the documentation and help that is available for... (1 Reply)
Discussion started by: wosis
1 Replies
9. Solaris
Hi all
Ive got a v440 with an external T3 RAID in a dual bus configuration. I need to add an additional JBOD extension to the disk array via two VDCH cables.
Now, can I do this as the server is live ? Can I just plug the two cables in, switch on the additional extension ? Will this cause... (1 Reply)
Discussion started by: sbk1972
1 Replies
10. IP Networking
Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten
Unable to get NIC working
Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies
pods::SDLx::Controller::State(3pm) User Contributed Perl Documentation pods::SDLx::Controller::State(3pm)
NAME
SDLx::Controller::State - the state of a SDLx::Controller::Interface
CATEGORY
Extension, Controller
SYNOPSIS
# you'll most likely get a State object from a SDLx::Controller::Interface
# object. Just in case, here's how you would construct one by hand:
my $state1 = SDLx::Controller::State->new;
my $state2 = SDLx::Controller::State->new( $x, $y, $v_x, $v_y, $rotation, $ang_v );
# attributes are just simple accessors:
$state->x(10);
$state->x; # 10
# same goes for the rest:
$state->y;
$state->ang_v;
# etc.
DESCRIPTION
A state object is a simple container for any given state inside a running SDLx::Controller::Interface instance.
METHODS
new()
new( $x, $y, $v_x, $v_y, $rotation, $ang_v )
Creates a new state container object. Can optionally set the initial value of all its attributes (see below).
ACCESSORS
x
Accessor to get/set the x value, usually used to position the item or check for collisions.
y
Accessor to get/set the y value, usually used to position the item or check for collisions.
v_x
Accessor to get/set the x velocity of the instance, for moving objects dynamically.
v_y
Accessor to get/set the y velocity of the instance, for moving objects dynamically.
rotation
Accessor to get/set the rotation of the object, in degrees (0..360).
ang_v
Accessor to get/set the angular velocity, for rotating objects dynamically.
AUTHORS
See "AUTHORS" in SDL
perl v5.14.2 2012-05-28 pods::SDLx::Controller::State(3pm)