10 More Discussions You Might Find Interesting
1. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
2. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
3. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
4. Solaris
Hi All ,
I have 2 DNS servers (BIND 9.6.1 -Solaris 10) .Its configured as master ,slave serves .Now i am recieving error messages related to zone transfer in both the servers as mentioned below .
Primar Server
named: client x.x.x.x#40825: transfer of './IN': sending zone data: ran... (1 Reply)
Discussion started by: sandeep.tk
1 Replies
5. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
6. Solaris
Hi all,
I have a server running an Oracle database that is part of a Solaris M5000 container. Presumably this is referred to as a zone within a cluster, not sure if I get the terminology right.
Anyway, a third-party manages the zone and unfortunately is not "helpful/friendly" to assist me on... (1 Reply)
Discussion started by: newbie_01
1 Replies
7. Solaris
I have an old Sun SparcStation 5 that is running Sun OS 5.7, I'm not sure which commands would allow me to obtain the DNS zone transfer settings?
1.) I'm needing to know if the zone transfers are enabled.
2.) If it is enabled, does it transfer to specific servers
3.) If so, how do I go about... (1 Reply)
Discussion started by: Fhistleb
1 Replies
8. Solaris
Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many... (1 Reply)
Discussion started by: fulhamfcboy
1 Replies
9. Windows & DOS: Issues & Discussions
Please help. Reply and tell me if you find one. Lots of thanks!
Computek (6 Replies)
Discussion started by: computek
6 Replies
10. IP Networking
Hi all,
How to deny any zone transfer out of my host??? bind 8.2.3
Thank you all,
Regards
:D (2 Replies)
Discussion started by: solvman
2 Replies
ldns-notify(1) General Commands Manual ldns-notify(1)
NAME
ldns-notify - notify DNS servers that updates are available
SYNOPSIS
ldns-notify [options] -z zone servers
DESCRIPTION
ldns-notify sends a NOTIFY message to DNS servers. This tells them that an updated zone is available at the master servers. It can perform
TSIG signatures and it can add a SOA serial number of the updated zone. If a server already has that serial number it will disregard the
message.
OPTIONS
-z zone
The zone that is updated.
-h Show usage and exit
-v Show the version and exit
-s serial
Append a SOA record indicating the serial number of the updated zone.
-p port
Use port as destination port (default the DNS port 53) for the UDP packets.
-y key:data
Use the given TSIG key and base64-data to sign the NOTIFY. Uses the hmac-md5 algorithm.
-d Print verbose debug information. The query that is sent and the query that is received.
-r num Specify the maximum number of retries before notify gives up trying to send the UDP packet.
EXIT CODE
The program exits with a 0 exit code if all servers replied an acknowledgement to the notify message, and a failure exit code otherwise.
AUTHOR
Written by the ldns team as an example for ldns usage.
REPORTING BUGS
Report bugs to <ldns-team@nlnetlabs.nl>.
COPYRIGHT
Copyright (C) 2005 NLnet Labs. This is free software. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
9 Jan 2007 ldns-notify(1)