Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Hi All ,
I have 2 DNS servers (BIND 9.6.1 -Solaris 10) .Its configured as master ,slave serves .Now i am recieving error messages related to zone transfer in both the servers as mentioned below .
Primar Server
named: client x.x.x.x#40825: transfer of './IN': sending zone data: ran... (1 Reply)
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Hi all,
I have a server running an Oracle database that is part of a Solaris M5000 container. Presumably this is referred to as a zone within a cluster, not sure if I get the terminology right.
Anyway, a third-party manages the zone and unfortunately is not "helpful/friendly" to assist me on... (1 Reply)
I have an old Sun SparcStation 5 that is running Sun OS 5.7, I'm not sure which commands would allow me to obtain the DNS zone transfer settings?
1.) I'm needing to know if the zone transfers are enabled.
2.) If it is enabled, does it transfer to specific servers
3.) If so, how do I go about... (1 Reply)
Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many... (1 Reply)
ZONESERVER(8) zoneserver ZONESERVER(8)NAME
zoneserver - handle zone transfers and other TCP functions for MaraDNS
DESCRIPTION
zoneserver listens on port 53/tcp and handles DNS zone transfers and any DNS query done over TCP instead of UDP. zoneserver uses a
configuration file, /etc/mararc by default, to determine its parameters.
USAGE
zoneserver -f pointer_to_mararc_file
OPTIONS -f Specifies the location of the configuration file. MaraDNS uses the same configuration file for both the main dns server and the
zoneserver.
CONFIGURATION FILE FORMAT
The file format for the mararc file can be found in the mararc(5) manual page. In particular, the zoneserver uses the zone_transfer_acl,
tcp_convert_acl, tcp_convert_server, bind_address, and recursive_acl mararc parameters.
EXAMPLE MARARC FILE
In this example mararc file, which is used both by maradns and zoneserver, we allow 10.1.2.3, 10.1.14.7, and 192.168.116.{any} to transfer
zones, and we allow anyone on the internet to perform TCP queries. The only zone served in this example is example.com:
ipv4_bind_addresses = "10.1.1.1" # Our IP
tcp_convert_server = "10.1.1.1" # IP of UDP DNS server
tcp_convert_acl = "0.0.0.0/0" # Anyone may do DNS-over-TCP
chroot_dir = "/etc/maradns" # Where zone files are
csv2 = {} # Initialize list of zone files
csv2["example.com."] = "db.example.com" # example.com zone file
# The next line is a list of who can transfer zones from us
zone_transfer_acl = "10.1.2.3, 10.1.14.7, 192,168.116.0/24"
SEE ALSO
The man pages maradns(8) and mararc(5)
http://www.maradns.org
BUGS
zoneserver assumes that the authoritative NS records are immediately after the SOA record, and that there is at least one non-NS between
that last authority NS record for the zone and the first delegation NS record.
IXFR requests are incremental zone transfers, meaning that the DNS server should only display records changed since the last IXFR request.
zoneserver, however, treats an IXFR as if it were an AXFR request, outputting all of the records for the zone in question.
zoneserver closes the TCP connection after transferring the requested zone.
If an unauthorized client attempts to connect to the zoneserver, zoneserver immediately disconnects the unauthorized client.
LEGAL DISCLAIMER
THIS SOFTWARE IS PROVIDED BY THE AUTHORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
AUTHOR
MaraDNS is written by Sam Trenholme. Jaakko Niemi used 5 minutes to put the original version this manpage together. Sam has subsequently
revised this manual page.
October 2001 zoneserver ZONESERVER(8)